TIMER mode
Setting the TIMER:
Press and hold S11 until the Timer “1” digit starts to blink. Press S1
interval timer “SEG 1 to 6”. Press S3 to set the hour, minute & second. Press S1
increase or decrease the value. Press S7 to exit setting.
Note: If there is no key operation within 3-4 minutes in this mode, the watch will auto
exit to Time mode.
ALARM mode
Setting the ALARM:
Press S7 from TIMER mode to enter ALARM mode. The watch will display the
view. Press and hold S11 until the Alarm “1” digit starts to blink. Press S1
the Alarm 1 to 5. Press S3 to set the hour, minute, Time, Alarm and Chime.
For Chime, press S1/S5 to turn it ON or OFF. Also note when
tone is automatically ON and the Chime icon appears in all modes. Likewise, if
is OFF the Key tone is automatically OFF.
Alarm setting in SET mode:
•
Select ALARM then press S3
•
Select ALARM 1 to ALARM 5 by pressing S1/S5 and then press S
•
Set the HOUR. Press S1/S5 to change values. Press S3 to enter
•
Set the MINUTE. Press S1/S5 to change values. Press S3 to enter
•
Set the alarm time referred to T1 or T2. Press S1/S5 to change. Press S
•
Set the alarm ON or OFF. Press S1/S5 to change. Press S3 to enter
•
Set the Chime ON or OFF. Press S1/S5 to change. Press S3 to enter
•
Press S7 to exit alarm setting
SET mode
Press S7 from ALARM mode to SET mode. 1.5 seconds later the watch will display the
setting options: Press S5 the ff. Sequence are as follows; AUTO LAP,
USER, NIGHT, CONTRAST, CHIME, ALARM and TIMER. Press S
option to set. Press S1/S5 to select then press S3 to enter. Press S7 to exit
Time mode.
Setting the Auto Lap:
The same setting procedure applies in setting the time in Alarm setting
Note: Alert sub-mode, press S3 to enter ALERT function. When alert is set to
will be a beep sound during taking auto lap. When it is set to
sound.
Setting the Time/ Alarm/ Timer/ User:
. Press S1/S5 to select the
hour, minute & second. Press S1/S5 to
4 minutes in this mode, the watch will auto
he watch will display the alarm
. Press S1/S5 to select
the Alarm 1 to 5. Press S3 to set the hour, minute, Time, Alarm and Chime.
to turn it ON or OFF. Also note when Chime is ON, the Key
is automatically ON and the Chime icon appears in all modes. Likewise, if Chime
and then press S3 to enter.
to enter
to enter
to change. Press S3 to enter
to enter
to enter
mode. 1.5 seconds later the watch will display the
AUTO LAP, TIME, UNIT,
. Press S3 to enter selected
Press S7 to exit setting to
Alarm setting mode.
to enter ALERT function. When alert is set to ON, there
will be a beep sound during taking auto lap. When it is set to OFF, there is no beep
The same setting procedure applies in setting the time in
Setting the UNIT:
Press S3 to enter. Press S1/S5 to select KM or Mi
Setting the DISPLAY (LCD contrast):
Press S3 to enter. Press S1 or S5 to change the setting. Press S
and exit.
Setting the Chime:
Press S3 to enter. Press S1/S5 to select ON or
Setting the NIGHT mode:
Press S3 to enter. Press S1/S5 to select the following options:
sec.
10 SECONDS – Press S11 will turn ON the Light
20 SECONDS – Press S11 will turn ON the Light for 20 sec
NIGHT ON – Light will continuously ON when CHRONO is running
am. But when CHRONO is stopped or reset from 6:00 pm to 7:00 am, press any key can
turn ON the light for about 10 seconds.
Press S3 to accept the selected setting. Press S7 to exit.
Battery:
Watch is using a rechargeable Lithium Ion battery that will re
hours charging time using the USB cable. While battery is charging, the watch cannot
be used and all buttons are disabled. User needs to recharge the battery when the
watch indicates a “low battery”.
Note: Battery Life
(fully charge battery);
8 hrs min
HRM ON) in day time within the time period from
(continues GPS with CHRONO ON, HRM ON and Light
6 pm to 7 am. This means, after 7 or 8 hours
walking, etc., the battery power become low and the watch will display “LOW BATT”.
GPS watch troubleshooting guide:
PROBLEM/ QUESTION
SOLUTION/ ANSWER
How to turn off the GPS
Press and hold S9 for
turn OFF the GPS.
I cannot get a GPS signal
Take your GPS watch outdoors and away from tress
and tall buildings. Remain stationary and try acquiring
GPS signal again. Be sure that the antenna is pointing
towards the sky
Can I reset the watch?
You can reset the watch by pressing S1, S5, S7, and
S11 together. The date and time will be reset to default
The same setting procedure applies in setting the time in Alarm setting mode.
or Mi.
to change the setting. Press S3 to confirm setting
OFF.
ollowing options: Night ON, 10 sec and 20
urn ON the Light for 10 seconds.
will turn ON the Light for 20 seconds.
continuously ON when CHRONO is running from 6:00 pm to 7:00
am. But when CHRONO is stopped or reset from 6:00 pm to 7:00 am, press any key can
to accept the selected setting. Press S7 to exit.
Watch is using a rechargeable Lithium Ion battery that will require approximately 4.5
hours charging time using the USB cable. While battery is charging, the watch cannot
be used and all buttons are disabled. User needs to recharge the battery when the
min. (continues GPS with CHRONO ON,
from 7 am to 6 pm. While approx. 7 hours
(continues GPS with CHRONO ON, HRM ON and Light ON) within the time period from
hours continues activity such as running,
, the battery power become low and the watch will display “LOW BATT”.
SOLUTION/ ANSWER
Press and hold S9 for about 5 seconds from any view to
turn OFF the GPS.
Take your GPS watch outdoors and away from tress
and tall buildings. Remain stationary and try acquiring
GPS signal again. Be sure that the antenna is pointing
towards the sky for better signal reception.
You can reset the watch by pressing S1, S5, S7, and
S11 together. The date and time will be reset to default
Summary of Contents for GPS 2.0 Watch
Page 9: ......
