Sole Fitness E55, Owner'S Manual

Page: 11 / 38

9 E55 / E95 ELLIPTICAL
HARDWARE
STEP 1
1. Install the Incline Rail Assembly ( 2 ) into the U-channel bracket of the Main
Frame ( 1 ). Secure with the six bolts & associated hardware as follows: From
the sides install two Hex Head Bolts ( 133 ) with two Flat Washers ( 164 ) and
two Nylon Nuts ( 157 ). From the top install four Hex Head Bolts ( 135 ), four
Split Washers ( 182 ), four Flat Washers ( 170 ), and four Star Washers ( 183 ), and
tighten with the Wrenches provided ( 184 & 187 ). Connect the three wire
2. Locate the Console M ast ( 12 ) and Console Mast Cover ( 96 ) and slide the Cover
onto the Mast as far as it will go. Make sure the Console Mast Cover is facing
the correct way. At the top opening of the Main Frame of the elliptical is a
Computer Cable ( 50 ); Secure the free end of the twist tie that exits the
bottom of the console mast (12) to this cable. Pull the opposite end of this
twist tie up through the console mast (12) until the cable exits the top.
Install the Console Mast ( 12 ) into the receiving bracket on the top of the Main
Frame ( 1 ). Pull slightly on the computer cable at the top of the mast while
installing. This will ensure the cable does not get pinched and shorted during
console mast assembly.
3. Put one Split Washer ( 180 ) onto the Long Hex Head Bolt ( 125 ) and install
through the left side of the receiving bracket into the Console Mast ( 12 ). Put
the two Curved Washers ( 181 ) onto the two Short Hex Head Bolts ( 132 ) and
install through the front of the console mast. Using Wrench ( 184 ), tighten
the ( 132 125 ) bolt, and lastly the fourth bolt, which is
lead to noise and instability issues.
4. Plug all of the connectors into the back of the console; Computer Cable ( 50 ),
two Hand pulse Cables ( 56 ), Resistance switch wire ( 59 ) and Incline switch
wire ( 61 ). Secure the Console ( 45 ) on the console mounting plate with four
Phillips Head Screws ( 141 ).
INCLINE
RAIL
& CONSOLE
MAST
1
See Page 10 for Illustration
1. Install four Wave Washers (1
75
) onto the Left and Right sides of the Handle
Bar axle, two on each side.
2. Slide the Left (
10
) and Right (
11
) Handle Bars onto the appropriate side of
the axle. The handlebars have a small sticker on them indicating L (left) and R
(right).
Make sure the handlebars are facing the correct direction – see illustration.
3. Install two Flat Washers (
165
) onto the two Hex Head Bolts (
132
) and install,
and tighten, in the threaded holes in the ends of the axle.
4. Connect the two wires (Left-
60
to
61
& Right-
59
to
61
) on the L&R sides
together and store the excess wire, including plastic connectors, back inside
the console mast. Place the rubber grommets (
75
) over the wire and snap it
into the hole in the console mast. Install the Handle Bar Covers (
105
to
106
)
and (
107
to
108
) over the Console Mast axle connections and secure with the
eight Sheet Metal Screws (
142
).
HANDLE
BAR
2
HARDWARE STEP 2
See Page 10 for Illustration
#164 . 3/8” x 19 x 1.5T
Flat Washer (2 pcs)
#170
. 5/16” x 20 x 1.5T
Flat Washer (4 pcs)
#181 . 3/8” x 23 x 2T
Curved Washer (2 pcs)
#180
. 3/8” x 2T
Split Washer (1 pcs)
#141 . M5 x 10mm
Phillips Screw (4 pcs)
#157 . 3/8” x 7T
Nylon Nut (2 pcs)
#182
. 5/16” x 1.5T
Split Washer (4 pcs)
#183 . 5/16”
Star Washer (4 pcs)
#132
. 3/8” x 3/4”
Hex Head Bolt (2 pcs)
#135 . 5/16” x 2-1/4”
Hex Head Bolt (4 pcs)
#133 . 3/8” x 1-1/2”
Hex Head Bolt (2 pcs)
#125
. 3/8” x 2-1/4”
Hex Head Bolt (1 pcs)
#175 . 25mm
Wave Washer (4 pcs)
#165 . 3/8” x 30mm
Flat Washer (2 pcs)
#142
. 3.5 x 12mm Sheet
Metal Screw (8 pcs)
#132 . 3/8” x 3/4”
Hex Head Bolt (2 pcs)
power connector (48) and Sensor Connector (49) to the mating connectors.
Note: there will be an empty four pin port on the back of
the console. This model doesn’t use this port.