Quick Installation Guide
——
Triple Power Lithium-ion Battery
Packing List (BMS)
I
Packing List (Battery Module)
II
Installation Prerequisites
III
Floor/Wall Mounting
IV
Battery Module Installation to Base Mounting
V
Place the BMS on top of the battery module and affix it with M4 screws using an L-type wrench. Ensure that the BMS and
battery unit align on matching sides as shown in the diagram below.
Battery Module Installation to Module
VI
-
Tighten the expansion screw sleeve
- Drill holes(at least 80mm) with driller
- Mark the postion of the holes
BMS Installation to Battery Module
VII
Note: The Quick Installation Guide briefly describes required installation steps. If you have any questions, refer to the User
Manual enclosed with the BMS for more detailed information.
(
193±2) mm
Make sure the wall is strong enough to withstand the weight of battery.
-Adjust the balance
NOTE!
NOTE!
Ensure that the installation location meets the following conditions:
The building is designed to withstand earthquakes
The location is far
the sea to avoid salt water and humidity,
1000m
from
over
The floor is flat and level
There are no flammable or explosive materials, at a minimum of 0.9m
The ambience is shady and cool, away from heat and direct sunlight
The temperature and humidity remain at a constant level
There is minimal dust and dirt in area
There are no corrosive gases present, including ammonia and acid vapor
Where charging and discharging, the ambient temperature ranges from 0°C to 45°C
The Triple Power battery module is rated at IP65 and thus can be installed outdoors as well as indoors. However,
if
installed outdoors, do not allow the battery pack to be exposed to direct sunlight and moisture.
If the ambient temperature exceeds the operating range, the battery pack will stop operating to protect itself.
The optimal temperature range for operation is -10°C to 50°
Frequent exposure to harsh temperatures may
C.
deteriorate the performance and lifetime of the battery module.
ŸŸŸŸŸŸŸŸŸŸ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
In practice, the requirements of battery installation may be different due to enviroment and locations.
In that case, follow up the exact requirements of the local laws and standards.
Step 3: Match the battery with base mounting
For two battery
s:
module
Place the second one on top of the module and two sides are locked with M4 screws.
·
Match the BMS to the battery modules
Fix the battery module and wall bracket with expansion bolts.
·
Place the BMS on top of the module and two sides are locked with M4 screws(N).
Note: One battery module or connected to the BMS, need to be installed a bracket to fix.
·
Charging Cable (+) x1 (2m)
Power Cable(0.12m) x1
CAN Cable x1 (2m)
Wall Bracketx1
Expansion Bolt x2
Expansion Screw x2
M4 Screw x2
Base M
x1
ounting
User Manual x1
Rotation Wrench x1
M5 Screw x2
Flat Gasket x2
Expansion Bolt x2
Copyright Declaration
The copyright of this manual belongs to SolaX Power Co.,Ltd.. Any corporation or
individual should not plagiarize, partitially copy or fully copy(including software,etc.),
and no reproduction or distribution of it in any form or by any means. All rights
reserved.
SolaX Power Co.,Ltd,.reserves the right of final interpretation. The information is
Triple Power Lithium-ion Battery
User Manual
30Ah
Charging Cable (-) x1 (2m)
COMM Cable x1 (0.2m)
Ring Terminal x1
Guard Ring x2
BMS x1
Accessories (1) of the
three and four Battery Modules (HV10230×3
/
4):
Accessories (2) of the three and four Battery Modules (HV10230×3
/
4):
Quick Installation Guide
--Triple Power Lithum-ion Battery
Quick Installation Guide
--Triple Power Lithum-ion Battery
Note:The two power cables need to be purchased separately
One
Battery Module (HV10230 ×1):
Power Cable (690mm) x1
COMM Cable (600mm) x1
M4 Screw x2
Power Cable (1200mm) x1
COMM Cable
(1200mm) x1
Power Cable(1200mm) x1
Power Cable(1800mm) x1
Expansion Bolt x2
Base M
x1
ounting
Guard Ring x4
Cover Plate x1
Quick Installation Guide x1
Accessories of Wall bracket x1
Quick Installation Guide x1
Snap-fit x2
Battery Module x1
M4 Screw x2
