background image

5.5 Installation steps

Step2:Hang the X3 inverter onto the wall bracket.

Transporting the inverter need at least 2 persons, each one needs to 
use the handles at the both sides of the inverter each.
Hang the X3 inverter onto the bracket, make sure the support on the 
bracket is 

x

ed well with the inverter.

5.6 Connections of the PV power system

PV String

WARNING!

WARNING!

WARNING!

The X3 Series inverters has two input areas”A”and “B”,each with its own MPPT 
tracker, can be connected in series into 2-strings PV modules. Please select 
PV modules with excellent function and reliable quality. Open-circuit 
voltage of module arrays connected in series should be less than Max. DC 
input voltage; Operating voltage should be conformed to MPPT voltage 
range.

Step1: Screw the wall bracket on the wall

Use the wall bracket as a template to mark the position of the six holes.
Drill holes with 

φ

10 driller carefully, make sure the holes are deep enough for 

install and tight the expansion tubes.
Install the expansion tubes in the wall, and screw the wall bracket using the 

screws in the screw package.(

φ

10 driller.torque: 2.5

±

0

.

2Nm)

Step2

Step1

Loading capacity  and hardness of the supporting surface, load rating of 
mounting bracket should be at least four times the weight of the devices 
according to IEC 62109-1 and supporting characteristic will be impaired by 
wear, corrosion, material fatigue or ageing. This should be calculated by 
inspection of the design data of supporting material and consulting 
construction engineer.

PV module voltage is very high which belongs to dangerous 
voltage range, please comply with electric safety rules when 
connecting.

When the photovoltaic array is exposed to light, it supplies a DC 
voltage to the PCE.

When there is something wrong with the modules arrays. 
Modules can be connected with inverter only after eliminating 
these problems.

Danger!
DangertolifeduetohighvoltagesonDCconductors.
whenexposedtosunlight,thepvarraygeneratesdangerousDC
voltagewhichispresentintheDCconductors.TouchingtheDC
conductorscanleadtolethalelectricshocks.
CoverthePVmodules.DonottouchtheDCconductors.

Summary of Contents for X3-30.0-T-D
























Reviews: