SolaX Power T-BAT H 10.0 User Manual Download Page 4

Slave3

2

Safety

2.1   Safety Instructions

For safety reasons, installers are responsible for familiarizing themselves with the 

contents of this manual and all warnings before performing installation.

2.1.1 

General Safety Precautions

2. Safety

Observe the following precautions: 

Risks of explosion: 

Risks of fire: 

Do not subject the battery module to heavy impacts.

Do not crush or puncture the battery module.
Do not dispose of the battery module in a fire. 

Do not expose the battery module to temperatures in excess of 140°F (6°C).

Do not place the battery module near a heat source, such as a fireplace.
Do not expose the battery module to direct sunlight.

Do not allow the battery connectors to touch conductive objects such as 
wires.

Risks of electric shock: 

Do not disassemble the battery module.

Do not touch the battery module with wet hands.
Do not expose the battery module to moisture or liquids.
Keep the battery module away from children and animals.

Risks of damage to the battery module: 

Do not expose the battery module to liquids.

Do not subject the battery module to high pressures.
Do not place any objects on top of the battery module.

 

 

WARNING!

Do not crush or impact the battery, and always dispose of it 

according to safety regulations.

                                

    
    

    

    

CAUTION!

 

3

2. Safety

                                

2.1.2 

Explanation of Symbols

2.1.2 

Explanation of Symbols

    

    

Symbol

Explanation

The inverter complies with the requirements of the applicable 

CE guildlines.

Observe enclosed documentation.

Keep the battery system away from open flames or ignition

sources.

Keep the battery system away from children.

The battery module may explode.

The battery system must be disposed of at a proper facility 

for environmentally-safe recycling.

The battery system should not be disposed of together 
with household waste. Disposal information can be found 

in the enclosed documentation. 

Danger of high voltages.

Danger. Risk of electric shock.

TUV mark for IEC62619

Compliant with UKNI standards.

Compliant with UKCA standards.

T-BAT SYS-HV should only be installed for residential applications and not be for 

commercial applications.

If the battery is not installed within one month after receipt, it must be 
charged for maintenance. Non-operational batteries should be discarded 

according to local regulations.

    

    

Symbol

Explanation

Keep the battery system away from open flames or ignition

sources.

The battery module may explode.

The battery system must be disposed of at a proper facility 

for environmentally-safe recycling.

Keep the battery system away from children.

CSA mark for UL1973

272687

CE mark of conformity

TUV certification

Do not dispose of the battery together with household 
waste.

Read the enclosed documentation.

Caution, risk of electric shock

Caution, risk of danger

Fcc mark of conformity

Summary of Contents for T-BAT H 10.0
















Reviews: