background image

 

L10US-IB20, L10US-IB40, L10US-IB60 L10US-IB00, L15US-IB40,  

L15US-IB60 L15US-IB00, L20US-IB60, L20US-IB00 UPS 

 

2.

 

Important Safety Instructions (Save These Instructions) 

SAVE THESE INSTRUCTIONS!

 This manual contains important instructions for Model L10US, 

L15US and L20US that should be followed during installation and maintenance of the UPS 
and batteries.  

L10US External DC Circuit Over current Protective Device - "CAUTION - To reduce the risk of 
fire, connect only to a circuit provided with DC 100 amperes maximum branch circuit over 

current protection in accordance with the National Electric Code, ANSI/NFPA 70”.

 

L15US External DC Circuit Over current Protective Device - "CAUTION - To reduce the risk of 
fire, connect only to a circuit provided with DC 120 amperes maximum branch circuit over 

current protection in accordance with the National Electric Code, ANSI/NFPA 70”.

 

L20US External DC Circuit Over current Protective Device - "CAUTION - To reduce the risk of 
fire, connect only to a circuit provided with DC 160 amperes maximum branch circuit over 

current protection in accordance with the National Electric Code, ANSI/NFPA 70”.

 

WARNING! 

When backfeed protection is needed by local area regulations and codes, please 

note that it is not a part of the system design and you must install an external automatic 
isolation device on site, in order to prevent dangerous voltage or energy in the input of the 
isolation device. The device must be rated according to the system specifications and must 
open within 15 seconds after the upstream power supply fails.  

HAZARD!

 If those instructions are not followed it may cause death or serious injury. 

A label of this text or equivalent text in your language, must be installed on the UPS

, a

nd on 

the backfeed isolator protection if it

 is

 installed remotely from the UPS. 

 

CAUTION!

 (UPS having Internal Batteries): Risk of electrical shock 

 Hazardous 

live parts inside this unit are energized from the battery supply even when the 
input AC power is disconnected. 

CAUTION!

 (No User serviceable Parts): Risk of electrical shock, do not remove 

cover. No user serviceable parts inside. Refer servicing to qualified service 
personnel. 

CAUTION!

 (Non-isolated Battery supply): Risk of electric shock, battery circuit is 

not isolated from AC input, hazardous voltage may exist between battery 
terminals and ground. Test before touching. 

 

 

WARNING! (Fuses): To reduce the risk of fire, replace only with the same type 
and size of fuse. 

Summary of Contents for L10US-IB00









































































Reviews: