Solar Stik PRO-VERTER 7000-120 Instruction Manual Download Page 12

Page: 12 / 12

April 2020 | Solar Stik®, Inc.

12 |

PRO-Verter 7000 Inverter/Charger Replacement

E. Installation of the Replacement Inverter/Charger

F. PRO-Verter Functional Test

1. After disconnecting all electrical and mechanical connections, cafefully lift out the old Inverter/

Charger while checking for any missed electrical connections.

2. Lower the replacement unit down into the PRO-Verter, taking great care not to stress or break

any wires in the PRO-Verter case. This step will require at least two people.

3. Reestablish all electrical and mechanical connections using this Instruction Manual and the

images taken during disassembly.

4. Rebuild the baffle box. Remove the old tape from the plastic walls before reinstalling.

Replacement tape is included in the kit.

1. Move the Faceplate back into it normal, operating location.

2. Connect the PRO-Verter to an active 24 VDC battery. Turn on the PRO-Verter main power

breaker. Observe power-up on PRO-Verter LCD user interface.

3. If the PRO-Verter does not power up, ensure all original connections are reestablished.

Summary of Contents for PRO-VERTER 7000-120












