Solaira Alpha H1 Reference Manual Download Page 6

1.          Securely  fasten  the  L-shaped  wall  brackets  to  the  mounting  surface  using 
             both  of  the  fixing  holes  in  the  short  part  of  the  bracket  (see  Fig.  H  for  
             mounting hole template centres). Please refer to Table 1 for recommended         
             positioning  of  the  heater.  Please  note.  wall  fixings  are  not  supplied.  They 
             should be selected to substantially support the   weight  of  the  installation.  If 
             in doubt contact a professional for advice! 
 
2.

Fix  the  heater  assembly  to  the  brackets  via  the  hole  in  the  centre  of  the  
joining  bar.  The  joining  bars  should  slide  inside  the  gap  of  the  two  wall      
brackets. 

 
3.

Place  a  bolt  and  washer  in  the  hole  of the  wall  bracket  and  put  a serrated 
washer  on  the  opposite  side  between  the  bracket  and  joining  bar.  Repeat 
on opposite side. 

 
4.

Fit the heater assembly to the brackets and place a washer and nut on the 
bolts protruding through the joining bars. 

 
5.

Fully tighten the nut and bolts (Fig. G) with the heaters set as shown in Fig. 
F. 

 
6.          Secure  the  supply  cables  so  they  do  not  rest  on  the  body  or  obstruct  air-
             vents. 
 

Always isolate the heater from the mains supply when adjusting the angular 
position.

 

Fig. G 

C h a i n   H a n g i n g  - 
T w o   S i n g l e   H e a t e r s   J o i n e d  

 

When two Alpha heaters are joined they can also be chain hung 
from a ceiling (Fig. J). 

 

Please refer to Table 1 for the recommended positioning of the 
heater with regards to minimum distances. Do not install the heater 
in a corner! 

 

Always  allow  the  heater  to  cool  before  attempting  to  reposition/
move. Never attempt to move the heater while it is switched on! 

 

Observe the minimum safe distance between the heater body and   
inflammable surfaces and objects when mounting. 

 

Keep out of the reach of children. 

 
1.          Please refer to  Table  1  for  recommended  positioning  of  the 
             heater.  When  hanging  from  a  ceiling  two  chains  of  equal 
             length  and  gauge  are  required  and  should  be  selected  with 
             fixings that are adequate to hold the weight of the heater. If in 
             doubt contact a professional for advice!  
 
2.

Attach  the  heater  assembly  to  the  chains  via  the  hole  in  the 
centre  of  the  joining  bar  as  shown  in  Fig.  J.  and  ensure  the 
heater faces directly down when hanging. 

 
3.          Secure  the  supply  cable  so  they  do  not  rest  on  the  body  or          
             obstruct the air-vents. 
 

Always isolate the heater from the mains supply when adjusting 
the position.

 

Fig. J 

Fig. H 

DRILLING HOLE TEMPLATE DIMENSIONS 

FOR WALL MOUNTED BRACKETS 

Summary of Contents for Alpha H1













Reviews: