Solahart Streamline Electric Owner'S Manual Download Page 6

ABOUT YOUR WATER HEATER 

SAFETY 

This water heater is supplied with a thermostat, an over-temperature energy cut-out, temperature sensors, a 
pressure  relief  valve  and  a  combination  temperature  pressure  relief  valve.  These  devices  must  not  be 
tampered with or removed. The water heater must not be operated unless each of these devices is fitted and 
is in working order. 
 
The operation of the over-temperature cut-out on the thermostat indicates a possibly dangerous situation. If 
the  over-temperature  cut-out  operates,  it  must  not  be  reset  and  the  water  heater  must  be  serviced  by  a 
qualified person. 
 
If  the  electrical  conduit  to  the  solar  storage  tank  is  damaged,  it  must  be  replaced  by  a  qualified  person  in 
order to avoid a hazard. Phone your nearest Solahart Dealer to arrange for an inspection. 
 

 

Warning:

  For  continued  safety  of  this  water  heater  it  must  be  installed,  operated  and  maintained  in 

accordance with the Owner‟s Guide and Installation Instructions. 
 

The Solahart warranty may not cover faults if relief valves or other safety devices are tampered with 
or if the installation is not in accordance with these instructions. 

 

PRECAUTIONS 

Where  damage  to  property  can  occur  in  the  event  of  the  water  heater  leaking,  the  water  heater  must  be 
installed in a safe tray. Construction, installation and draining of a safe tray must comply with AS/NZS 3500.4 
and all local codes and regulatory authority requirements. 
 
The  water  heater  must  be  maintained  in  accordance  with  the  Owner‟s  Guide  and  Installation  Instructions. 
Refer to 

“Regular Care”

 on page 10 and to 

“Anode Inspection and Replacement”

 on page 13. 

 
If this water heater is to be used where an uninterrupted hot water supply is necessary for your application or 
business  you  should  ensure  that  you  have  back  up  redundancy  within  the  hot  water  system  design.  This 
should  ensure  the  continuity  of  hot  water  supply  in  the  event  that  this  water  heater  were  to  become 
inoperable for any reason. We recommend you seek advice from your plumber or specifier about your needs 
and building back up redundancy into your hot water supply system. 
 

SOLAR MONITOR 

The solar storage tank incorporates a solar monitor. The solar monitor is located on the lower front cover and 
houses both a green and a red LED. 
 
The green LED, marked “Solar”, indicates the current operational mode of the solar water heater and the red 
LED, marked “Attention”, indicates a fault mode. 
 
The green LED will emit either a constant glow or a series of flashes, with a 2 second interval between each 
series. 
 
The  red  LED  will  emit  a  series  of  flashes,  with  a  2 second  interval  between  each  series,  only  if  there  is  a 
particular fault condition with the system. 
 
The operational modes are: 
 

Flashes 

Operational Modes 

 

solid green 

(remains on) 

Standby mode 

2 x green 

Flooding solar circuit 

3 x green 

Pump flow control 

4 x green 

Pump flow established 

5 x green 

Tank at maximum temperature 

no green 

(remains off) 

Call for service 

 
If  the  power  supply  to  the  water  heater  is  on  and  the  green  LED  is  off  or  the  red  LED  is  flashing,  this 
indicates  there  is  a  fault  with  the  water  heater.  The  red  LED  may  emit  up  to  six  flashes  in  each  series  of 
flashes. Count the number of flashes and phone your nearest Solahart Dealer to arrange for an inspection. 

Summary of Contents for Streamline Electric





























































Reviews: