Solahart Streamline Electric Owner'S Manual Download Page 5

ABOUT YOUR WATER HEATER 

HOW HOT SHOULD THE WATER BE? 

The solar control unit will circulate the closed circuit fluid through the 
solar  collectors  until  a  temperature  of  approximately  75°C  is 
reached in the solar storage tank. 
 
During periods of low solar energy gain,  the water temperature can 
be  boosted  by  the  thermostatically  controlled  electric  booster 
heating unit. Refer to 

“Booster Control”

 on page 7. 

 
Solahart  recommends  the  thermostat  is  set  at  60°C  to  maximise 
solar contribution. 
 

Note:

  AS 3498  requires  that  a  water  heater  provides  the  means  to 

inhibit the growth of Legionella bacteria in potable water. This water 
heater  can  satisfy  this  AS 3498  requirement  provided  the  electric 
booster is energised for a sufficient period each day and the electric 
booster thermostat setting is 60°C or higher. 
 

HOTTER WATER INCREASES THE RISK OF SCALD INJURY 

This  water  heater  can  deliver  water  at  temperatures  which  can 
cause  scalding.  Check  the  water  temperature  before  use,  such  as 
when  entering  a  shower  or  filling  a  bath  or  basin,  to  ensure  it  is 
suitable for the application and will not cause scald injury. 
 
We recommend and it may also be required by regulations that an approved temperature limiting device be 
fitted into the hot water pipe work to the bathroom and ensuite when this water heater is installed. This will 
keep the water temperature below 50°C at the bathroom and ensuite. The risk of scald injury will be reduced 
and still allow hotter water to the kitchen and laundry. 
 

TEMPERATURE ADJUSTMENT 

The  water  heater  features  a  tradesperson  adjustable  thermostat.  This  requires  a  licensed  tradesperson  to 
make  any  temperature  adjustments.  The  thermostat  has  a  maximum  temperature  setting  of  70°C  and  a 
minimum temperature setting of 60°C. 
 
We  advise  you  have  your  electrician  adjust  the  thermostat  to  the  lowest  setting  which  meets  your  needs, 
especially  if  there  are  young  children  or  elderly  people  in  the  home.  Refer  to 

“Hotter Water  Increases  the 

Risk of Scald Injury”

 on page 5. 

 

 WARNING 

This water heater is only intended to be operated by persons who have the experience or the knowledge and 
the capabilities to do so. This water heater is not intended to be operated by persons with reduced physical, 
sensory or mental capabilities i.e. the infirm, or by children. Children should be supervised to ensure they do 
not interfere with the water heater. 
 
This  water  heater  uses  240 V  AC  electrical  power  for  operation  of  the  control  systems  and  the  electrically 
operated components. The removal of the front covers will expose 240 V wiring. They must only be removed 
by a qualified person. 
 
Care should be taken not to touch the pipe work connecting the solar storage tank and the solar collectors. 
Very  high temperature closed circuit fluid can  be generated  by the solar collectors under certain conditions 
and flow through the pipe work from the solar collectors to the solar storage tank. 
 
Should the water from the water heater appear blue or if blue closed circuit fluid is noticed around the base 
of the water heater, this indicates a leak of the closed circuit fluid from the heat exchanger. The closed circuit 
fluid  is  non-toxic  and  not  hazardous  to  health.  Phone  your  nearest  Solahart  Dealer  to  arrange  for  an 
inspection. 
 

 

 

typical maximum 

temperature from solar 

gain 

maximum recommended 

supply temperature to 

bathrooms and ensuites 

minimum booster setting 

maximum booster setting 

Summary of Contents for Streamline Electric





























































Reviews: