Soil Instruments Digital Inclinometer Pro User Manual Download Page 11

Page: 11 / 51

The front panel has three LED indicators and a power button.

FRONT PANEL

LED’S

Press to switch on. Press again to switch off. The Power LED glows green

when power is on. The reel switches off automatically after 5 minutes

without a bluetooth connection or after 10 minutes if no commands

and data are transmitted between tablet and probe.

POWER BUTTON

& POWER LED

The Comms Ready/Bluetooth LED blinks slowly while the Bluetooth reel

waits for a connection, then glows a steady blue when the connection

is made.

COMMS READY/

BLUETOOTH LED

The Battery LED stays off during normal use. A fully-charged battery

provides about 40 hours of operation. If the battery charge is very low,

the Battery LED blinks red when you first switch on the reel.

BATTERY LED

Battery LED

Comms Ready/
Bluetooth LED

Power Button & LED

BEFORE YOU GO

TO SITE

•

Unpack the Digital Inclinometer Pro, retaining the packaging for

future carriage to Soil Instruments for calibration.

•

Charge the Digital Inclinometer Pro by carefully following the

charging procedure below;

•

Check that there is sufficient battery power in the tablet by

tapping on the battery icon located on the top right hand side of

the home screen. Ideally the battery should be over 50%; however

the tablet will function at a lower level

QUICK START GUIDE

Using the Digital Inclinometer Pro

Summary of Contents for Digital Inclinometer Pro




















































Search results

Summary of Contents for Digital Inclinometer Pro

Reviews:

Related manuals for Digital Inclinometer Pro

Brands by name

Popular brands

Soil Instruments Digital Inclinometer Pro, User Manual

Search results

Summary of Contents for Digital Inclinometer Pro

Reviews:

Related manuals for Digital Inclinometer Pro

Brands by name

Popular brands