Sohn 6503 Installation & Service Manual Download Page 4

GENERAL SAFETY RULES

WARNING

READ THE FOLLOWING INSTRUCTIONS BEFORE OPERATING THIS MACHINE

This machine was designed for certain applications only. Sohn Manufacturing strongly
recommends that this machine not be modified and/or used for any application other than that for
which it was designed. If you have any questions relative to a particular application, DO NOT use
the machine until you have first contacted Sohn Manufacturing to determine if it can or should be
performed on the machine. As with all machinery, there are certain hazards involved with the
operation of the product. Using the machine with respect and caution will considerably lessen the
possibility of personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator may result. Safety equipment such as guards, goggles and hearing
protection can reduce your potential for injury. But even the best guard won’t make up for poor
judgment, carelessness or inattention.

and exercise

in the

workplace.

:Your personal safety is your responsibility.

1. DO NOT OPERATE THIS MACHINE UNTIL it is assembled and installed according to the

instructions. FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE
OPERATING THE MACHINE.

Follow all wiring codes and recommended electrical

connections. Learn the machine’s application and limitations as well as the specific hazards
peculiar to it. OBTAIN ADVICE from your supervisor, instructor, or another qualified person
if you are not familiar with the operation of this machine.

2. DO NOT OPERATE MACHINE WITHOUT GUARDS IN PLACE.

3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. NEVER

START THE MACHINE before clearing the web of all objects (tools, scrap pieces, etc.)

4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use this machine in damp or wet

locations, or expose them to rain. Keep work area well lighted.

5. KEEP CHILDREN AND VISITORS AWAY. Children and visitors should be kept a safe

distance from work area.

6. WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or other

jewelry to get caught in moving parts. Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.

7. KEEP ARMS, HANDS, FINGERS away from all moving parts of the machine. DON’T

OVERREACH. Keep proper footing and balance at all times.

8. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not

recommended by Sohn Manufacturing may cause hazards or risk of injury to persons.

Always use common sense

caution

REMEMBER

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY

3

Summary of Contents for 6503































Reviews: