background image

edgeGate - Quick Startup Guide

8

© Softing Industrial Automation GmbH

2.3

Safety precautions

CAUTION

This product contains a lithium backup battery. The lithium content is less than 1 g. The
battery has been successfully tested by the manufacturer in accordance with the "Manual of
Tests and Criteria" of the United Nations (UN), Part III: Classification procedures, test
methods and criteria, sub-section 38.3.
If the product is handled properly, this battery does not need to be replaced during the
lifetime of the product. Therefore, opening the product is unnecessary and not permitted. The
product must only be operated within the specified temperature range. Do not expose to heat
above this temperature range and keep away from open fire. Store in a dry place. Improper
handling of lithium batteries can cause the batteries to ignite or explode and pose a burn
hazard to users.

CAUTION

During operation, the device's surface will be heated up. Avoid direct contact. When servicing,
turn off the power supply and wait until surface has cooled down.

Note

Do not open the edgeGate housing. It does not contain any parts that need to be maintained
or repaired. In the event of a fault or defect, remove the device and return it to the vendor.
Opening the device will void the warranty!

Summary of Contents for data FEED edgeGate

























Reviews: