SoftBank Whiz Quick Manual Download Page 2

2

3.Teaching a Cleaning Route

Press the Main power switch to 

turn it on ( l )

Tap "TEACH ROUTE"

Use the cleaning modes (Normal mode / Max 

   power mode) according to the condition of the floor.

When teaching a cleaning route manually, switching 

   cleaning modes while cleaning will be duplicated 

   during autonomous cleaning.

3

Pull the Steering Handle straight up 

until you reach the joint and tilt the 

handle to lock it into position

Move the Machine to the Home 

Location Code

Scan the Home Location Code

If an error is displayed in a red frame, 

adjust the distance of the Machine and 

the code and scan it again.

Select "+" to save a new route

1

2

3

4

5

6

8

9

Press the Vacuum Power Button

Select a teach mode of cleaning route

Teach boundary/ cleaning 

route of the entire cleaning area

(teaching)

Even if you pause during 

teaching, it will not affect the 

cleaning when carried out 

autonomously. Please clean 

at your own pace.

Backward movements 

will not be recognised 

as a cleaning route.

7

60cm (2.0ft)

80cm (2.6ft)

Clean only boundary for an automatic 

route creation and cleaning route 

for a manual route creation.

The charging status light 

flashes in orange.

1.Open the battery door

2. Press the battery lock

3. Pull the battery halfway out 

    toward you 

Pull the bottom left of the 

battery door toward you.

Press the battery lock

with your right thumb.

Recharge the battery

6. Insert the battery in the 

     battery compartment 

Once the battery is properly inserted, 

the lock in the battery compartment 

will pop into place, making a "click".

Pull the battery out toward you as you 

release your thumb from the lock. 

Be careful not to let your thumb get 

caught.

5. Insert the battery into 

    the charger

4. Remove the battery from

    the Machine 

Hold the handles with both hands 

when pulling the battery out.

Pull out the battery from the Machine and recharge it in the charger. About 4 hours are required for the battery to be fully recharged. The battery operates for 

about 3 hours when cleaning in normal mode.

The Charging 

Status Light

*Once the battery is recharged, 

 the charging status light flashes in green.

Saving the cleaning route will take half

the time of teaching the cleaning route.

Scan the Home Location Code 

again

11

10

After the cleaning is finished, press 

the Vacuum button and turn off the 

cleaning mode

A warning screen about escalators or 

other moving platforms appears.

Check it and tap "CONFIRM".

For each Home Location Code, six cleaning   

   routes can be saved. 

A screen appears for checking whether there are 

   any escalators or other moving platforms. 

   Check the cleaning area and tap "NO".

Summary of Contents for Whiz

Page 1: ... the Home Location Code HLC at a permanent location where autonomous cleaning will start stop flat against a wall or a pillar If the HLC needs to be moved place it at the same location whenever the Machine runs autonomously Please note that cleaning may not be performed correctly if the installation of HLC is slightly off 80cm 2 6ft 60cm 2 0ft 1 Names of Parts This document contains information on...

Page 2: ...tery lock 3 Pull the battery halfway out toward you Pull the bottom left of the battery door toward you Press the battery lock with your right thumb Recharge the battery 6 Insert the battery in the battery compartment Once the battery is properly inserted the lock in the battery compartment will pop into place making a click Pull the battery out toward you as you release your thumb from the lock B...

Page 3: ...ous cleaning Operate in a time when there are few passerby and objects around the cleaning area For safety the Machine will operate slightly away from the wall When cleaning areas close to the wall operate manually Stow the Steering Handle Remove the Notification Pager from the Machine and carry it with you during autonomous cleaning As for a cleaning route created automatically its autonomous cle...

Page 4: ...erates and move it to an appropriate place as required When recreating the original layout is difficult teach a cleaning route again Close curtains to block light in a place where there is sunlight Adjust the brightness in a place where there are lights or LED lights Wipe the sensors with the attached Micro fiber cloth When the change of the layout takes place after teaching the cleaning route rec...

Reviews: