Instruction Manual
Instruction Manual
•
Input voltage: 100-240VAC 50/60Hz
•
Power: Max.24W
•
Lumen: Max.2200LM
•
Bluetooth Version: Bluetooth V2.1+ EDR
•
Transmission distance: 10 meters
•
Signal-noise ratio: ≥75dB
•
Frequency response range: 87-108MHz
•
Speaker output power: Max.2x3W
•
USB charging function: Max.5V 1A
•
Socket output power: 3680W（220-240V）/1875W（110-120V）
•
Power cord: H05RN-F 3x1.0mm2 1.8 meters
•
Protection class: IP44
1. Product specification
3. Product usage (SNT-WL22FM)
3.1 How to use the lighting
0-225°
adjustable
3.2 How to use the Bluetooth speaker（a) / FM radio（b)
3.3 With waterproof socket (Figure A)
and waterproof USB charging
port (Figure B)
•
In the case that power is on, press "BT" button to turn on the Bluetooth with the warning
tone. Then turn on the Bluetooth on your mobile device and search for Bluetooth name of
“WL30BT”. Connect Bluetooth with short
“beep”, and the music can be played immediately.
•
Turning off the Bluetooth on the phone can terminate the connection. Only when the
first device exits can a second device be connected.
•
After pressing the "BT" button, if it has not been connected to a Bluetooth device within
five minutes, the work lamp will automatically turn off the Bluetooth function with
warning tone. Please press the "BT" button again when using it. Press “BT” button
can turn off the Bluetooth.
•
In the case that power is on, press "FM" button to turn on the FM radio, and it will display
the same channel as last time displayed. Press “ ”and “ ” button can adjust the
frequency with 0.1MHz, long press for at least 2 seconds can search the channel
automatically. Press “FM” button again can turn off the radio.
Thank you for choosing the portable SNTLUX LED work lamp with Bluetooth Speaker. We hope this product also
allows you to enjoy the joy of music at work and the convenience of listening to the Internet Radio. Please take good
care of this instruction manual for future use.
A
B
C
D
ON
OFF
2. Product components and dimensions (mm)
1
1
2
3
4
254
73
200
LED light board
2
Switch
3
Waterproof socket
4
Audio system
5
Operation buttons
6
USB charging port
Audio system
Figure A
Figure B
Please firmly insert the
plug into a live socket.
The improper contact
between the plug and
socket would cause
the damage to the
equipment.
Press the button “DIM” when the switch is
“ON”, and adjust the brightness of LED light
board, which are respectively 2200LM, 600LM
and 1200LM, appeared in repetitive cycle.
The switch will not control this socket .
When the power plug is inserted into the
external socket, the socket will be on the
work state all the time. USB charging port
will be under control of switch.
Angle can be adjusted as
per sketch, it can also be
used as a desk lamp when
it stays at 225
°
.
Press switch button "ON",
the LED light will be the
brightest at this time. And
when the switch is in
“OFF”, the LED light will
be switched off.
200
205
128
6
5
FM
V
+
V
-
FM
V
+
V
-
•
If the LED light is not needed during music playing, long press the “DIM” button to turn off the light temporarily,
and re-press“DIM”to activate the light again. When turning on the Bluetooth speaker will turn off the FM
radio function automatically, also turning on the FM radio will turn off the Bluetooth speaker automatically.
•
The volume can be adjusted by the volume keys on the phone ( under Bluetooth mode) or by the pressing
buttons “V+”and“V-”on the lamp.
a)
b)
c)
All manuals and user guides at all-guides.com
