SNT ACL2 120 Installation, Operation And Maintenance Manual Download Page 2

 WARNING

Read this manual before installing, operating or maintaining this actuator. Failure to 
follow safety precautions and instructions could cause actuator failure and result in 
serious injury, death or property damage. 

This manual provides important information on how to work with the actuator safely 
and efficiently. The manual is part of the device, must always be kept in the device’s 
direct proximity and should be available for personnel to read at any time. Failure to 
comply  with  the  installation,  use  and  maintenance  instructions  indicated  in  this 
manual  will  result  in  immediate  termination  of  the  warranty  conditions  of  the 
actuator and completely relieve S

NT

 from any liability for damage caused to persons

and / or property. 

S

NT 

does  not  assume  direct  or  indirect  responsibility  for  an  improper  use  of  the

actuator, not respecting the performances of the actuator declared in the catalogs. 

The manufacturer will not be liable for damage to the actuator or the equipment into 
which the actuator has been installed resulting from: 

• disregarding this manual
• unintended use
• employment of untrained personnel
• unauthorized conversions
• technical modifications
• manipulation or removal of the screws on the device
• use of unapproved spare parts

The  aforementioned  conditions  are  therefore  not  contemplated  and  entail  the 
immediate  termination  of  the  guarantee  and  the  immediate  decay  of  any 
responsibility on the part of S

NT

.

S

NT 

reserves the right to make changes to the actuators and this manual without

giving any notice. 

Summary of Contents for ACL2 120























Reviews: