manualshive.com logo in svg

SNOWJOE Sunjoe SWJ701E-RM, Operator'S Manual

Share
Download
SNOWJOE Sunjoe SWJ701E-RM Operator'S Manual Download Page 20

20

Troubleshooting

The motor does not start 

when you switch it on

•  Cord not connected to 

the power source

•  Incorrect chain tension

•  Incorrect chain tension

•  Trigger switch not 

operational

Bar and chain running hot 

and smoking

Motor runs but chain is not 

rotating

Poor cutting performance

Chain jumps off guide bar

Chain works with difficulty

•  Make sure that the cord is connected to a 

power source

•  Check chain tension

•  Check chain tension

•  Check safety lock button is fully depressed prior 

to engaging the trigger switch

Fault

Possible Cause

Remedy

•  Extension cord not 

connected to the plug

•  Extension cord or power 

cable damaged

•  Worn motor brushes

•  Check extension cord is fully connected to the 

tool 

•  Repair or replace the damaged cord

•  Motor brushes must be replaced

•  Chain tension too tight

•  Oil tank empty

•  Chain installed backwards

•  Adjust chain tension

•  Fill tank with chain oil

•  Reverse chain so that cutters face the right direction

•  Chain tension too tight

•  Guide bar and chain may 

be damaged

•  Adjust chain tension

•  Replace the chain and bar with the identical 

replacement part

• 

Blunt saw chain

•  Incorrect chain tension

•  Saw chain fitted incorrectly

•  Sharpen or replace the saw chain

•  Check chain tension

•  Check saw chain orientation

Summary of Contents for Sunjoe SWJ701E-RM

























Reviews:

No comments

Brands by name

Popular brands

Load more brands