background image

4

and cell damage. Do not leave batteries in the charger for 

days on end.

8.  Never use or charge batteries if you suspect that it has 

been more than 12 months since the last time they were 

charged. There is a high probability that the battery pack 

has already suffered dangerous damage (exhaustive 

discharge).

9.  Charging batteries at a temperature below 50°F (10°C) will 

cause chemical damage to the cells and may cause a fire.

10. Do not use batteries that have been exposed to heat 

during the charging process, as the battery cells may have 

suffered dangerous damage. 

11. 

Do not use batteries that have suffered curvature or 

deformation during the charging process or those that 

exhibit other atypical symptoms (gassing, hissing, 

cracking, etc.).

12. Never fully discharge the battery pack (maximum 

recommended depth of discharge is 80%). A complete 

discharge of the battery pack will lead to premature aging 

of the battery cells.

Protection from environmental influences

1.  Wear suitable work clothes. Wear safety goggles.
2.  Protect your cordless tool and the battery charger from 

moisture and rain. Moisture and rain can cause dangerous 

cell damage.

3.  Do not use the cordless tool or the battery charger near 

vapors and flammable liquids.

4.  Use the battery charger and cordless tools only in dry 

conditions and at an ambient temperature of 50-104°F 

(10-40°C).

5.  Do not keep the battery charger in places where the 

temperature is liable to reach over 104°F (40°C). In 

particular, do not leave the battery charger in a car that is 

parked in the sunshine.

6.  Protect batteries from overheating. Overloads, 

overcharging and exposure to direct sunlight will result 

in overheating and cell damage. Never charge or work 

with batteries that have been overheated – replace them 

immediately, if possible.

7.  Store the charger and your cordless tool only in dry 

locations with an ambient temperature of 50-104°F  

(10-40°C). Store your lithium-ion battery pack in a cool, 

dry place at a temperature of 50-68°F (10-20°C). Protect 

the battery pack, charger and cordless tool from humidity 

and direct sunlight. Only place fully charged batteries in 

storage (charged to at least 40%).

8.  Prevent the lithium-ion battery pack from freezing. Battery 

packs that were stored below 32°F (0°C) for more than  

60 minutes must be discarded.

9.  When handling batteries, be wary of electrostatic charge. 

Electrostatic discharges can damage the electronic 

protection system and the battery cells. Avoid electrostatic 

charging and never touch the battery poles.

Risk of Explosion

•  Do not spray flammable liquids.
•  Do not use acids, bases, solvents, or any flammable 

material in this product. These substances can cause 

physical injuries to the operator and irreversible damage to 

the machine.

Additional Safety Instructions

•  High-pressure: keep clear of nozzle.
•  Injection hazard: equipment can cause serious injury if the 

spray penetrates the skin.

•  Do not point the gun at anyone or at any part of the body.
•  In case of skin penetration, seek medical aid immediately.
•  Before servicing, cleaning, or removing any parts, shut off 

the power and relieve pressure.

•  This machine is not suitable for connection to the potable 

water mains.

•  Do not spray electrical apparatus and

 wiring. 

• 

ARCING PARTS – Keep the motor at least 20 ft (6 m) away 

from explosive vapors.

• 

m

CAUTION! Gun kicks back. Hold trigger with both 

hands.

Product Description

Purpose

•  This cordless high-pressure power washer is intended 

for residential use to clean vehicles, machines, buildings, 

facades, etc.

Areas of Application

•  Never use the machine in potentially explosive areas under 

any circumstances!

•  The operating temperature must be between 32ºF (0

ºC) and 

104ºF (40ºC).

•  The machine consists of an assembly with a pump, which 

is encased in a shock-absorbing housing. To provide the 

operator with an optimal working position, the machine is 

equipped with a spray wand and a non-slip handle grip, 

whose shape and configuration comply with applicable 

regulations. 

•  Do not cover or modify the spray wand or the spray nozzles 

in any way.

•  The cordless high-pressure washer is designed to be used 

with cold or lukewarm water; higher temperatures can 

damage the pump.

•  Do not use water that is dirty, gritty, or contains any 

chemical products, as these could impair operation and 

shorten the life of the machine.

Summary of Contents for Sunjoe SPX6001C-XR









































































Reviews: