background image

11

12. Check that the electrical supply voltage and frequency 

(Volt/Hz) correspond to those specified on the pressure 

washer rating plate. If the power supply is correct, you 

may now plug the pressure washer into the power outlet 

(Fig. 13).

 

NOTE: The GFCI may need to be reset when first plugged 

into the electric outlet. Press the "Reset" button until the 

power light indicator on the GFCI illuminates.

Operation

m

IMPORTANT!

 This pressure washer is equipped with 

a micro-switch sensitive to water flow. This Total Stop System 

(TSS) senses water flow in the pump. When the trigger is 

released, water stops flowing through the pump. The TSS then 

automatically turns the motor off to protect the pump from 

overheating, thus saving energy and prolonging pump life.

1.  Turn the water supply tap on completely.
2.  Release the safety lock, then press the trigger for a few 

seconds until the water flow is steady. Operating the 

pressure washer in this manner will allow air to escape and 

discharge residual pressure in the hose (Figs. 14 and 15).

3.  Turn the ON/OFF switch (pressure select dial) to the LOW (I) 

or HIGH (II) position to start the pressure washer (Fig. 16).

Using the adjustable spray nozzle

m

WARNING!

 High-pressure jets can be dangerous if 

subject to misuse. The jet must not be directed at persons, 

pets, live electrical equipment, or the appliance itself.

1.  The spray wand is equipped with an adjustable nozzle.
2.  The water pressure can be adjusted to low pressure (–) 

and high pressure (+) by turning the pressure adjustment 

knob. The nozzle tip can be adjusted from pencil spray 

(wide open tip) to fan spray (narrow tip) by turning the 

nozzle tip adjustment knob (Fig. 17).

 NOTE: 

When using the unit with detergent, the spray 

nozzle has to be set into low pressure and fan spray. The 

pressure settings on the spray nozzle are only meant to 

work with detergent, it will not affect the overall working 

pressure of the unit. 

RESE

T

TEST

Fig. 13

GFCI

Power light 

indicator

Reset

Fig. 14

Trigger

Safety lock

Fig. 15

STOP

LO

W

0

HIGH

Fig. 16

Summary of Contents for SUNJOE SPX4003-RM





















Reviews: