5
Information about the charger and the
charging process
1. Please check the data marked on the rating plate of the
battery charger. Be sure to connect the battery charger
to a power supply with the voltage marked on the rating
plate. Never connect it to a different mains voltage.
2. Protect the battery charger and its cord from damage.
Keep the charger and its cord away from heat, oil and
sharp edges. Have damaged cords repaired without delay
by a qualified technician at an authorized Snow Joe
®
+
Sun Joe
®
dealer or call the Snow Joe
®
+ Sun Joe
®
customer service center at 1-866-SNOWJOE
(1-866-766-9563).
3. Electrical plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
grounded appliances. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
4.
Keep the battery charger, battery packs and the cordless
tool out of the reach of children.
5.
During periods of heavy use, the battery packs will
become warm. Allow the battery packs to cool to room
temperature before inserting them into the charger to
recharge.
6.
Do not overcharge batteries. Do not exceed the maximum
charging times. These charging times only apply to
discharged batteries. Frequent insertion of a charged or
partially charged battery pack will result in overcharging
and cell damage. Do not leave batteries in the charger for
days on end.
7. Never use or charge a battery if you suspect that it has
been more than 12 months since the last time they were
charged. There is a high probability that the battery pack
has already suffered dangerous damage (exhaustive
discharge).
8. Charging batteries at a temperature below 41°F (5°C) will
cause chemical damage to the cells and may cause a fire.
9.
Do not use batteries that have been exposed to heat
during the charging process, as the battery cells may have
suffered dangerous damage.
10.
Do not use batteries that have suffered curvature or
deformation during the charging process or those that
exhibit other atypical symptoms (gassing, hissing,
cracking, etc.)
11.
Never fully discharge the battery packs (maximum
recommended depth of discharge is 80%). A complete
discharge of the battery packs will lead to premature
aging of the battery cells.
Protection from environmental influences
1. Wear suitable work clothes. Wear safety goggles.
2. Protect your cordless tool and the battery charger from
moisture and rain. Moisture and rain can cause dangerous
cell damage.
3. Do not use the cordless tool or the battery charger near
vapors and flammable liquids.
4. Use the battery charger and cordless tools only in dry
conditions and at an ambient temperature of 50ºF – 104°F
(10°C – 40°C).
5. Do not keep the battery charger in places where the
temperature is liable to reach over 105°F (40.5°C).
In particular, do not leave the battery charger in a car that
is parked in the sunshine.
6.
Protect batteries from overheating. Overloads,
overcharging and exposure to direct sunlight will result
in overheating and cell damage. Never charge or work
with batteries that have been overheated – replace them
immediately, if possible.
7. Store the charger and your cordless tool only in dry
locations with an ambient temperature of 50ºF – 104°F
(10°C – 40°C). Store your lithium-ion battery packs in a
cool, dry place at a temperature of 50 – 68°F (10 – 20°C).
Protect the battery packs, charger and cordless tool from
humidity and direct sunlight. Only place fully charged
batteries in storage.
8.
Prevent the lithium-ion battery packs from freezing.
Battery packs that were stored below 32°F (0°C) for more
than 60 minutes must be discarded.
9.
When handling batteries, be wary of electrostatic charge.
Electrostatic discharges can damage the electronic
protection system and the battery cells. Avoid electrostatic
charging and never touch the battery poles.
Additional Safety Instructions
Safety Instructions for Walk-Behind
Snow Blowers
•
Read the operator’s manual carefully – Learn your snow
blower’s applications and limitations as well as the specific
potential hazards related to this machine. Do not use this
machine for any purpose other than the one for which it
was designed. Failure to adhere to these precautions may
cause mechanical defaults, serious damage, or personal
injury.
•
Preliminary unit inspection – Thoroughly inspect the
unit before use. Make sure all the parts are secure and
installed correctly. If you notice any abnormalities, do not
use the machine until it has been properly repaired. Always
perform a test run the first time you use the snow blower
or after replacing parts to ensure that the unit is functioning
properly.
•
Preliminary area inspection – Clear the area to be plowed
before each use. Remove all objects such as rocks, broken
glass, nails, wire, or string, which can be thrown by or
Summary of Contents for 24V-X2-SB18U-CT-RM
Page 20: ...snowjoe com...
