background image

Snapper 3500 PSI Pressure Washer

4

KNOW YOUR PRESSURE WASHER

Read this owner’s manual and safety rules before operating your high pressure washer.
Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.

Chemical Injection Siphon/Filter

Air Filter — Protects engine by filtering dust and debris out
of intake air.

Automatic Cool Down System — Cycles water through
pump when water reaches 140°-145°F. Warm water will
discharge from pump onto ground. This system prevents
internal pump damage.

Chemical Injection Siphon/Filter — Use to siphon
detergent or other pressure washer chemicals into the low
pressure stream.

Choke Lever — Prepares a cold engine for starting.

Fuel Valve — Used to turn fuel on and off to engine.

Gas Tank — Fill tank with regular unleaded gasoline. Always
leave room for fuel expansion.

High Pressure Hose — Connect one end to the water
pump and the other end to the spray gun.

High Pressure Outlet with Quick Connect — To
connect high pressure hose.

Nozzle Extension with Quick Connect — Allows you to
switch between four different spray nozzles.

Oil Fill Cap/Dipstick — Fill engine with oil here.

Pressure Control Knob — Varies the pressure of the high
pressure spray.

Pump — Develops high pressure.

Recoil Starter — Use for starting the engine manually.

Rocker Switch - Set this switch to "On" before using
recoil starter. Set switch to "Off" to switch off engine.

Spray Gun — Controls the application of water onto
cleaning surface with trigger device. Includes safety latch.

Spray Nozzles — Chemical injection, 0°, 15°, 25°, and 40°:
for various cleaning applications.

Throttle Lever—Sets engine in starting mode for recoil
starter. Operate normally in fast speed.

Water Inlet — Connect garden hose here.

Spray Gun

Nozzle Extension with

Quick Connect

High Pressure Hose

Rocker Switch
Throttle Lever

Choke Lever

Fuel Valve

Recoil Starter

(on front of engine)

Air Filter

Fuel Tank

Pressure

Control Knob

Pump equipped with 
Automatic Cool Down System

Water Inlet

Oil Fill Cap/Dipstick

Spray Nozzles

High Pressure Outlet
with Quick Connect

Summary of Contents for SnapperPro 1662-0

























Reviews: