Starting the Engine
1. While sitting in the operator’s seat, make sure the
PTO switch is disengaged, the parking brake is
engaged, and the ground speed levers are locked in
the START/PARK position.
2. Set the engine speed control to the CHOKE position.
NOTE
: A warm engine may not require choking.
3. Insert the key into the ignition switch and turn it to
START.
4. After the engine starts, move the engine speed con-
trol back to the FAST position. Warm up the engine
by running it for at least a minute before engaging the
PTO switch or driving the rider.
5.
after warming the engine, aLWaYS operate the
rider at fULL ENGINE SPEED when mowing.
In the event of an emergency the engine can be
stopped by simply turning the ignition switch to
STOP.
Use this method only in emergency situations.
For normal engine shut down follow the procedure given
in
Stopping the Rider and Engine
.
Stopping the Rider and Engine
1. Return the ground speed levers to the middle (or
neutral ‘N’
) position to stop rider movement. Pivot the
levers outward to lock them in the START/PARK posi-
tion.
2. Disengage the PTO by pushing down on the PTO
switch.
3. Engage the parking brake by moving the parking
brake lever forward and to the right.
4. Move the engine speed control to the SLOW position
and turn the ignition key to OFF. Remove the key.
Mowing
1. Make sure the PTO switch is disengaged, the parking
brake is engaged, the ground speed levers are locked
in their START/PARK positions, and the operator is in
the seat.
2. Start the engine (see
Starting the Engine
).
3. Set the mower cutting height (see
Cutting Height
Adjustment
).
4. Set the engine speed control to FAST.
5. Disengage the parking brake.
6. Engage the PTO by pulling up on the switch.
7. Pivot the ground speed levers in from the START/
PARK position to the neutral ‘N’ position.
8. Begin mowing. See
Operator Safety
for tips on safe
mowing practices.
9. When finished, shut off the PTO.
10. Stop the engine (see
Stopping the Rider and
Engine
).
Pushing the Rider by Hand
1. Disengage the PTO, engage the parking brake, lock
the ground speed levers into their START/PARK posi-
tions, turn the ignition OFF, remove the key, and wait
for all moving parts to stop.
2. To disengage the transmissions, pull the roll release
rods (
a
, Figure 2), located on either side of the
engine, up into the PUSH position.
3. Disengage the parking brake.
The rider can now be pushed by hand.
4. After moving the rider, re-engage the transmissions
by pushing the roll release rods back down to the
DRIVE position.
DO NOT TOW RIDER
Towing the unit will cause transmission dam-
age. Do not use another vehicle to push or
pull this unit.
figure 2. Roll Release components (On Each Side)
WaRNING
DO NOT disengage the transmissions and
coast down slopes. DO NOT use Roll Release
to disengage the transmissions unless machine
motion can be controlled and engine is off.
A
www.snapper.com
16
Not
for
Reproduction
Not
for
Reproduction
Summary of Contents for RZT26520
Page 31: ...31 en N o t f o r R e p r o d u c t i o n N o t f o r R e p r o d u c t i o n...
Page 32: ...www snapper com N o t f o r R e p r o d u c t i o n N o t f o r R e p r o d u c t i o n...
Page 63: ...31 es N o t f o r R e p r o d u c t i o n N o t f o r R e p r o d u c t i o n...
Page 64: ...www snapper com N o t f o r R e p r o d u c t i o n N o t f o r R e p r o d u c t i o n...
