background image

 

18 

Section 4 - ADJUSTMENTS & REPAIR 

 

WARNING 

Once blade is disengaged it should come to a stop 
in 3 seconds or less. If the blade continues to rotate 
after 3 seconds the blade brake must be adjusted. 
DO NOT continue to operate the machine if the blade 
brake is not operating properly. 

 
4.2.2.  BLADE BRAKE ADJUSTMENT 
The automatic Blade Brake should stop the blades 
within 3 seconds anytime the blades are 
disengaged by moving blade lever to the "OFF" 
position or by releasing the Blade Pedals. When 
the Blade Brake is properly adjusted there should 
be 1/8" to 1/4" clearance between the Blade 
Engagement Lever and the back of the Latch 
Plate. Check this by disengaging the Blade Lever 
and depressing the Blade Pedals as shown in 
Figure 4.2. If clearance is greater than 1/4" 
perform the following adjustment. 
1.  Remove Belt Cover. Refer to Section “BLADE 
BELT COVER REMOVAL”. 
2.  
With the blade engagement lever disengaged, 
hold the blade pedals down and measure the 
distance between the front of the blade lever and the 
rear of the latch plate. The dimension should be 1/8" 
to 1/4" clearance between lever and plate. See Figure 
4.5. If the dimension is incorrect go to step 3. 
3.  If dimension is greater than 1/4", rotate nut 
clockwise to increase brake tension. If dimension is 
less than 1/8", rotate nut counter-clockwise to 
decrease brake tension. See Figure 4.4. 
4.  Reinstall spindle cover. 
 

WARNING 

DO NOT operate machine until blade brake is 
adjusted and functioning properly. If blade stop time 
can not be achieved with the adjustment procedure 
described above, take machine immediately to an 
authorized Snapper dealer.

 

 

 

FIGURE 4.4 

 

FIGURE 4.5 

 

WARNING 

DO NOT attempt any adjustments, maintenance, service 
or repairs with the engine running. Stop engine. Stop 
blade. Engage parking brake. Remove key. Remove 
spark plug wire from spark plug and secure away from 
plug. Engine and components are HOT. Avoid serious 
burns, allow all parts to cool before working on machine. 
Fuel Filler Cap and Vent must be closed securely to 
prevent fuel spillage. 

 

4.2.3.  MOWER DECK ADJUSTMENT  

(Side-To-Side Levelness) 

Before making deck leveling adjustments, check the tire 
pressure.  Front tires 12 psi, rear tires 12 psi. If tires are 
properly inflated and mowing is still uneven, adjust side-
to-side deck levelness. 
1.  Place Rider on a smooth level surface. 
2.  Follow WARNING statement found on this page. 
3.  Place a piece of angle iron, pipe, or similar object 
under center of deck at the rear. 
4.  Remove rear hanger chains and allow center, rear of 
deck to rest on angle iron. 
5.  Measure the distance from blade tips to floor. If the 
measurement is within 1/8” from side-to-side, the deck 
attitude is satisfactory.  If difference from side-to-side is 
greater than 1/8”, continue with adjustment. 
6. Loosen the carriage bolt and nut retaining the left 
side of the front lift arm and adjuster. Only loosen the 
bolt and nut to the point where some tension remains 
but lift arm can be moved. 

 

FIGURE 4.6 

ROTATE NUT CLOCKWISE TO 
INCREASE BRAKE TENSION 

ROTATE NUT COUNTER CLOCKWISE TO 
DECREASE BRAKE TENSION 

BLADE 
LEVER 

1/8” TO 1/4” 

LATCH 
PLATE 

BLADE PEDAL 

CARRIAGE BOLT 
(not shown) 

FRONT LIFT ARM 

NUT 

SPACER 

Summary of Contents for M280919B





































Reviews: