Snapper ELT180H33IBV Safety Instructions & Operator'S Manual Download Page 19 | Manualshive

Page: 19 / 40

background image

19

Section 3 - MAINTENANCE

3.4 ANNUALLY (END OF EACH SEASON)

3.4.2. FUEL

FILTER

(Continued From Previous Page)
3.

Install new fuel filter part number 1-4359. See

Figure 3.14.

FIGURE 3.14

4.

Fill fuel tank with fresh gasoline. Refer to engine

owner's manual for fuel specifications.

3.4.3. SPARK

PLUG

Remove and replace engine spark plug. Refer to
engine owner's manual for correct replacement plug
and gap specifications.

3.4.4. HYDROSTATIC TRANSMISSION OIL

The hydrostatic transmission does not require
maintenance. If any problems arise return
immediately to a Snapper dealer.

3.5. SAFETY INTERLOCK SYSTEM CHECKS

This machine is equipped with an electrical safety
interlock system that is provided for the safety of the
operator and others. All safety devices must be in place
and functioning properly before operating the machine.
Perform the following interlock system checks
periodically during the operating season. Contact your
authorized Snapper dealer if you have questions.

WARNING

DO NOT operate machine if any safety interlock or
safety device is not in place and functioning
properly. DO NOT attempt to defeat, modify or
remove any safety device.

ENGINE MUST NOT START IF:

1)

Clutch/Brake Pedal not fully depressed OR,

2)

Blade Engagement Lever in the “ON” blades
engaged position.

ENGINE SHOULD START IF:

1)

Blade Engagement Lever in the “OFF” blades
disengaged position AND,

2)

Clutch/Brake Pedal fully depressed.

ENGINE MUST BEGIN TO STOP IF:

1)

Operator rises off of seat with Blade
Engagement Lever in “ON” blades engaged
position OR,

2)

Operator rises off of seat with Clutch/Brake
Pedal not fully depressed.

IMPORTANT:

Engine and blades will continue to

run if Operator becomes seated prior to engine
coming to a complete stop. After coming to a
complete stop, the Blade Engagement Lever must
be moved to the “OFF” position and the
Clutch/Brake Pedal fully depressed before engine
can be restarted. Engine and blades must come to a
complete stop within 5 seconds after the operator
rises off the seat or the blade switch is moved to the
“OFF” position.

NEW FUEL FILTER
PART NUMBER 1-4359

«
...
17
18
19
20
21
...
»

Summary of Contents for ELT180H33IBV









































Reviews:

No comments

Related manuals for ELT180H33IBV

Collector 543e Mono

Brand: Stiga Pages: 39

Brand: White Outdoor Pages: 4

Wheel Horse XL 320 71199

Brand: Toro Pages: 40

Brand: Yardworks Pages: 24

Brand: Gardeo Pages: 60

Brand: Aerotek Pages: 18

Brand: Troy-Bilt Pages: 40

Brand: Craftsman Pages: 56

Brand: Murray Pages: 68

Brand: Hitachi Koki Pages: 96

Brand: Surtek Pages: 17

Brand: Bushranger Pages: 20

PowerSafe 30WS/S Series

Brand: Ferrari Pages: 17

Brand: Husqvarna Pages: 44

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 60

Brand: Husqvarna Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands