background image

 

 

21 

TROUBLESHOOTING 

 

PROBLEM 

PROBABLE CAUSE 

CORRECTIVE ACTION 

Engine Will Not Start   1. Fuel tank empty. 

1. Fill fuel tank with fresh fuel/oil mix. 

Using Recoil Starter 

2. Engine needs choking and priming. 

2. Move choke control to “CHOKE” position. Push 

primer bulb three times. 

 

3. Spark plug wire disconnected. 

3. Place spark plug wire onto spark plug. 

 

4. Fuel shut off valve closed. 

4. Move fuel shut off valve to the on position. 

Engine Will Not Start  

Using Electric Starter 

1. Power extension cord not plugged into machine or    

120 Volt outlet for U.S.A. or 230 Volt for Europe. 

1. Plug power extension cord into machine & into 120 

Volt outlet for U.S.A. or 230 Volt for Europe. 

 

2. Power extension cord damaged. 

2. Discard damaged power extension cord. 

 

3. Starter switch damaged or faulty. 

3. Replace starter switch. 

Engine Stalls or Stops  1. Water, debris or stale fuel in fuel system. 

1. Drain and clean fuel system. 

After Running 

2. Choke control in the “CHOKE” position. 

2. Move choke control to “OFF” position. 

 

3. Fuel tank empty. 

3. Fill with fuel to proper level. 

 

4. Air intake clogged with snow or debris. 

4. Unclog air intake. 

 

5. Spark plug defective or gap set improperly. 

5. Service spark plug. 

Engine Loses Power  1. Engine lubrication oil level is low. 

1. Add oil to the engine to full level. 

 

2. Spark plug faulty. 

2. Service spark plug. 

 

3. Water, debris or stale fuel in fuel system. 

3. Drain and clean fuel system. 

Excessive Vibration 

1. Damaged, out of balance or bent auger. 

1. Service auger. 

 

2. Loose engine or auger/impeller components. 

2. Service and tighten loose components. 

 

3. Bent or loose Idler pulley. 

3. Tighten or replace pulley. 

 

4. Cracked, severed or frayed belt. 

4. Replace belt. 

Poor Snow 

1. Clogged discharge chute. 

1. Stop engine and unclog discharge chute. 

Discharging 

2. Damaged or bent auger/impeller or components. 

2. Service auger/impeller or components. 

 

3. Cracked, severed or frayed belt. 

3. Replace belt. 

 

4. Belt tension out of adjustment. 

4. Adjust belt tension. 

 

5. Insufficient lubrication in auger bearings. 

5. Lubricate all bearings as specified in manuals. 

 
 

SERVICE SCHEDULE 

 

ITEM

 

SERVICE PERFORMED

 

REF. EACH 

USE 

HRS 

25 

HRS 

50 

HRS 

100 

HRS 

EACH  

SEASON 

Spark Plug 

Replace Engine 

Manual 

    X   

Engine Oil 

Check Oil Level 

Engine Manual 

X        

 

 

Initial Oil Change 

Engine Manual 

 X      

 

 

Periodic Oil Change 

Engine Manual 

  X    

 

Air Filter 

Clean or Replace 

Engine Manual 

 

 

 

 

 

 

Engine Cooling 

System 

Clean Shroud & Fins 

Engine Manual 

    X   

Drive Belts 

Check For Adjustment, 
Wear and Tension 

Page 15-17 

  X 

X   X 

Auger & 
Impeller 

Check For Damage & 
Lubrication 

Page 13 

X        

Tires 

Check Air Pressure 

Page 8 

X        

 

 
 
 
 

Summary of Contents for E11306

























Reviews: