manualshive.com logo in svg

Snapper E11306, Safety Instructions & Operator'S Manual

Share
Download
Snapper E11306 Safety Instructions & Operator'S Manual Download Page 16

 

16 

Section 4 - REPAIR & ADJUSTMENTS 

 

WARNING 

Before attempting any adjustments, maintenance, 
service, or repairs, stop engine and auger/impeller, 
always remove key from ignition switch, remove 
spark plug wire and secure wire away from spark 
plug. Before tilting machine, drain all the fuel from 
fuel tank. Allow engine to run, outdoors where fumes 
can be safely dissipated, until all fuel is removed 
from carburetor. 

 
4.1.2.  AUGER BELT ADJUSTMENT 
 

(IDLER PULLEY ADJUSTMENT) 

 

(Continued From Previous Page) 

4.  Recheck cable for proper extension. 
5.  Reinstall belt cover. 
 
4.1.3.  AUGER DRIVE BELT REPLACEMENT 
Inspect belt frequently for signs of excessive wear. 
Visually check engine drive belt for cracking, 
fraying, severed or belt strands exposed. NOTE: 
Auger and Drive Belts are difficult to install. It may 
be necessary to allow an authorized Snapper 
Dealer to install these belts.  
1.  Remove belt cover. See Figure 4.2. 
2.  Remove discharge chute. 
3.  Unhook both idler springs. 
4.  Loosen auger/impeller belt guide. See Figure 4.4. 

IMPORTANT: Wheel  drive belt will have to be removed 
from around engine drive pulley and engine shaft to 
install auger drive belt. 

5.  Remove auger drive belt from around engine 
pulley. See Figure 4.4. 

 
 

 

 
 

FIGURE 4.4 

 

6.  Tilt machine forward to gain access to drive 
system area. Secure machine in the tilted position 
to prevent tipping over. Remove drive system cover 
plate. See Figure 4.5. 

 

 

 

FIGURE 4.5 

 

7.  Remove auger drive belt from drive disc pulley. 
Route auger belt through drive system in between 
rubber drive tire and drive disc. 
8.  Route new auger drive belt through drive 
system.  NOTE: New belt has to be routed in 
between rubber drive tire and drive disc to position 
it around auger pulley.  
9.  Reinstall wheel drive belt onto engine wheel 
drive pulley. Make sure belt is also positioned in the 
drive disc pulley groove. 
10.  Route auger drive belt around engine auger 
drive pulley. Make sure belt is also positioned in the 
drive disc pulley groove. 
11.  Position belt guide against auger drive belt and 
tighten securely.  
12.  Reinstall both idler springs. 
13.  Reinstall discharge chute, belt and drive system 
covers and tighten screws securely. 
14.  Reinstall drive system cover plate. 
15.  See Sections 4.1.1. & 4.1.2. Auger Belt 
Adjustment for new belt adjustment. Adjust belt as 
described in these sections. 

 
 
 
 
 
 
 
 
 

WHEEL DRIVE BELT 

BELT GUIDE 

AUGER DRIVE  
BELT 

SELF-TAPPING 
SCREWS 

REMOVE 
COVER 

UNHOOK IDLER 
SPRING 

UNHOOK  
IDLER 
SPRING 

Summary of Contents for E11306

























Reviews:

No comments

Brands by name

Popular brands

Load more brands