Snapper E11305 Safety Instructions & Operator'S Manual Download | Manualshive

Page: 6 / 24

background image

6

DECALS

Read, understand & follow all manuals and instructions
furnished with the Snowthrower.

YEAR OF MANUFACTURE

DANGER – ROTATING AUGER. KEEP AWAY.

SAFETY INSTRUCTIONS TO PREVENT INJURY:
1) Read Owner’s Manual for operating and safety

instructions.

2) Observe all labels and instructions.
3) DO NOT defeat safety features of controls. They

are for your protection.

4) Stop engine, wait for all moving parts to stop,

remove spark plug wire before unclogging or
servicing machine.

5) Never allow children to operate the equipment.

Never allow adults to operate equipment without
proper instruction.

6) Keep area of operations clear of all persons,

especially children.

7) Never direct discharge at bystanders or allow

anyone in front of unit.

8) Keep machine properly maintained and serviced

with all shields, guards, or protective devices in
place.

«
...
4
5
6
7
8
...
»

Summary of Contents for E11305

























Reviews:

No comments

Related manuals for E11305

Brand: Gardner Denver Pages: 45

Brand: Echo Pages: 26

Brand: Espina Pages: 18

Brand: Stihl Pages: 20

Brand: Simplicity Pages: 40

Brand: GreenWorks Pro Pages: 20

Brand: GreenWorks Pro Pages: 24

Brand: GreenWorks Pro Pages: 29

Wolf Garten Select SF Series

Brand: MTD Pages: 30

Brand: Shark Pages: 14

Brand: Shark Pages: 16

Brand: Snapper Pages: 8

Brand: Snapper Pages: 8

Brand: Snapper Pages: 24

Brand: Snapper Pages: 20

Brand: Flymo Pages: 52

Brand: Schmalz Pages: 2

SGBL-DG-1600-300-SO

Brand: Schmalz Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands