Snapper E11305 Safety Instructions & Operator'S Manual Download | Manualshive

Page: 17 / 24

background image

17

Section 4 - REPAIR & ADJUSTMENTS

WARNING

Before attempting any adjustments, maintenance,
service, or repairs, stop engine and auger/impeller,
always remove key from ignition switch, remove spark
plug wire and secure wire away from spark plug. Before
tilting machine, drain all the fuel from fuel tank. Allow
engine to run, outdoors where fumes can be safely
dissipated, until all fuel is removed from carburetor.

4.1.4.  WHEEL DRIVE BELT REPLACEMENT
Inspect belt frequently for signs of excessive wear.
Visually check engine drive belt for cracking,
fraying, severed or belt strands exposed. NOTE:
Auger and Drive Belts are difficult to install. It may
be necessary to allow an authorized Snapper
Dealer to install these belts.
1.  Remove belt cover. See Figure 4.2.
2.  Remove discharge chute.
3.  Unhook both idler springs.
4.  Loosen auger/impeller belt guide. See Figure 4.6.

IMPORTANT: Auger drive belt will have to be removed
from around engine drive pulley and engine shaft to
install wheel drive belt.

5. Remove wheel drive belt from around engine
pulley. See Figure 4.6.

FIGURE 4.6

6. Tilt machine forward to gain access to drive
system area. Secure machine in the tilted position
to prevent tipping over. Remove drive system cover
plate. See Figure 4.7.

FIGURE 4.7

7.  Remove wheel drive belt from drive disc pulley.
Route wheel belt through drive system in between
rubber drive tire and drive disc.
8.  Route new wheel drive belt through drive
system.  NOTE: New belt has to be routed in
between rubber drive tire and drive disc to position
it around auger pulley.
9.  Route wheel drive belt onto engine wheel drive
pulley. Make sure belt is also positioned in the drive
disc pulley groove.
10.  Reinstall auger drive belt around engine auger
drive pulley. Make sure belt is also positioned in the
drive disc pulley groove.
11.  Position belt guide against auger drive belt and
tighten securely.
12.  Reinstall both idler springs.
13.  Reinstall discharge chute, belt and drive system
covers and tighten screws securely.
14.  Reinstall drive system cover plate.

WHEEL DRIVE
BELT

BELT GUIDE

AUGER DRIVE
BELT

SELF-TAPPING
SCREWS

REMOVE
COVER

UNHOOK IDLER
SPRING

UNHOOK
IDLER
SPRING

«
...
15
16
17
18
19
...
»

Summary of Contents for E11305

























Reviews:

No comments

Related manuals for E11305

Brand: SNOWJOE Pages: 24

PB-413H - PARTS CATALOG SERIAL NUMBER P06413001001 -...

Brand: Echo Pages: 36

Brand: Gtech Pages: 12

Pro Sweep 07066

Brand: Toro Pages: 103

Brand: Nilfisk-Advance Pages: 26

Brand: Kärcher Pages: 374

Brand: Tanaka Pages: 12

Brand: Parkside Pages: 164

Brand: Cub Cadet Pages: 20

Brand: Jonsered Pages: 35

Brand: Toro Pages: 20

Brand: KRESS Pages: 8

Brand: KRESS Pages: 12

Brand: Haussmann Pages: 23

Brand: Power smart Pages: 24

SNOWSPORT HD Utility Plow

Brand: aci Pages: 16

Brand: CERTIFIED Pages: 44

Brand: Spectrum Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands