Snapper 500ZB2648 Dealer Setup & Adjustment Instructions Manual Download Page 2

Page: 2 / 16

500Z 26HP - 48” Mower Deck

TP 300-7368-IR-ZT-N

1/2008

Quick Setup List -

Page

Setup Procedure

Steps to Perform

Uncrating

❏

Remove Crate & Banding.

❏

Disengage Transmission Release Levers.

❏

Release Parking Brake and Roll Tractor forward off skid.

❏

Engage Transmission Release Levers.

Battery Installation

❏

Install Battery.

Tractor Assembly

❏

Assemble the Ground Speed Control Levers.

❏

Assemble the Seat.

Check Fluid Levels

❏

Check Engine Oil level.

❏

Check Hydraulic Oil level.

❏

Check Tire Pressure

Check Mower Assembly

❏

Check Blade Bolt Torque.

❏

Check & Adjust Deck Lift Rod Timing.

❏

Check & Level Mower Deck.

❏

Check Deck Drive Belt.

Lubrication &

❏

Lubricate all grease & oil points.

Fuel Preparation

❏

Add fuel.

❏

Start the Engine.

SAFETY CHECKS

❏

Check for LOOSE HARDWARE.

❏

Check all OPERATOR CONTROLS.

❏

Perform SAFETY INTERLOCK SYSTEM CHECK.

Summary of Contents for 500ZB2648

















Search results

Summary of Contents for 500ZB2648

Reviews:

Related manuals for 500ZB2648

Brands by name

Popular brands

Snapper 500ZB2648, Dealer Setup & Adjustment Instructions Manual

Search results

Summary of Contents for 500ZB2648

Reviews:

Related manuals for 500ZB2648

Brands by name

Popular brands