15
Specifications
A digital copy of this manual can be found at:
http://www.autonomic-controls.com/documents/Amplifiers/Manual_Instructions_Mirage_801e.pdf
Notes
• When a command is sent to an ampli-
fier it will first be transmitted on the
control bus and then returned to the PC
(Home Automation System). If an error
occurs an error will be returned instead
of the original command. The PC (Home
Automation System) needs to ignore its
command when it is returned.
• A Standby ON command implies that the
amplifier is not muted, if the amplifier
was previously Off, a mute command
must follow the Standby command if it
is muted.
• Not all Command and Data commands
are covered in this document.
• The expected reply for the "Send all
Parameters" command (09) is >144
bytes. All command fields listed in this
document are contained in the reply. The
reply also contains advanced commands
not listed in this document. The home
Automation or PC’s buffer should be
large enough to receive and process the
144-byte reply.
a. Zone 2 links to Zone 3.
b. Since Zone 2 is no longer linked to
Zone 1, Zone 1 will no longer be
linked to Zone 2.
c. Since Zone 3 is no longer linked to
zone 4, Zone 4 will no longer be
linked to Zone 3.
Example strings:
• 010A01: Standby ON command for Zone
10 amplifier.
• 012A01: Standby ON command for Zone
10 preamplifier.
• 060002: +2db Treble setting on Zone 0.
• 03IF02: Select Source 7 on Zone 31.
©2006–2019
Autonomic Controls, Inc.
Autonomic, eAudioCast, and TuneBridge are registered trademarks of Autonomic Controls, Inc.
All other trademarks are property of their respective owners. Specifications are based on current revision and may change without notice. 013119
Rated Output Power (FTC)
All Channels
55W per channel / 8Ω loads
75W per channel / 4Ω loads
Total Harmonic
Distortion (THD)
0.1% (50 Watt, 8 Ω load)
Damping Factor (8Ω load)
10
Speaker Impedance (Z1 - Z6 L/R)
4Ω–8Ω
Analog Input Sensitivity
(S1 - S8 L/R)
0.75V RMS (Vol 100, Gain 0dB, 55W Output)
Analog Input Impedance
(S1 - S8 L/R)
22KΩ
Digital Input sensitivity
0dBFS
Pre Amplifier Output Level and
Impedance (Z7 & Z8 L/R)
+14dB
Frequency Response
48 KHz sample rate: 10Hz - 22 KHz
96 KHz sample rate: 10Hz - 42 KHz
Tone Control
±12dB, 100Hz (Bass)
±12dB, 10kHz (Treble)
Signal to Noise Ratio
95dB (IHA-A, 0.75V input / unbalanced)
IR Output
(10) 3.5mm Jack: IR1 - IR8 current limited to 25mA
Source Inputs
(12) Digital Coaxial RCA, (8) Analog (L/R) RCA, (4) TOSLINK
Ethernet
(2) 100Base-T, MAIN IN and Switch EXT OUT
USB
(1) USB mini-B female 5 pin
Data
(1) 4 pole 3.5 mm terminal block connector (Data,12V, IR,0V)
Controllers
(8) RJ45 sockets Keypad controller ports
BUS RUN
(1) 4 way terminal block (0V, IR 12V & Data)
Amp On & PG Control
(1) 10 way terminal plug with Amp ON 1 - 8 and
(2) page preset contact closure inputs: PG1 & PG2
Zone Triggers & Presets
(1) 12 pole 3.5 mm terminal block connector
(Zone trigger 0V out, Zone trigger 1 - 8 12V out, Common, Preset 1 - 2 in)
Power Supply
110–240V AC 50–60Hz
Power Consumption
650W
Standby Power Consumption
6W
Dimensions with feet
4.0” H x 17” W x 15” D (10.2cm x 43.2cm x 38.1cm
Weight
15.4 lb. (7 kg)
Height including feet
105 mm
Touch Panel Display
2.4" color LCD touch panel display for menu guided control and programming.
Zones
(8) zones
Expandable to 96 zones, attaching additional M-801e or M-401e amplifiers
Acknowledgments – FreeRTOS – uIP
The M-401e firmware is based in part on FreeRTOS.org
™
V5.0.2 and the uIP TCP/IP stack.
For more information on FreeRTOS.org
™
please visit http://www.freertos.org. Source code for FreeRTOS.org™ can be downloaded from their official website.
The following copyright and statements for uIP TCP/IP stack are required by license: Copyright © 2001-2003, Adam Dunkels. All rights reserved.
1.Redistribution and use in source & binary forms, with or without modification, are permitted provided that the following conditions are met:
2.Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
3. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. The
name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
Summary of Contents for Mirage Autonomic MAS M-801e
Page 1: ...MAS m 801e 4 room Digital Amplifier with eAudioCast ...
Page 2: ......
