Snap-On ControlTech CTLNK1R240 Manual Download

Page: 24 / 36

Note: If LOCK is selected without a Preset configured, following screen is displayed:

Note: When Preset Lock is enabled, Clear Memory function is disabled and displays following Locked message if

attempted:

Note: When Preset Lock is enabled, Clear Cycle count function is disabled and displays Locked message if

attempted.

Preset Unlock

When Preset Lock is enabled, a password is required to access Configure menu. Refer to ControlTech™
Calibration Manual for Configure password.

From target torque or angle screen, press and hold ENTER button for 3 seconds.

Highlight

CONFIGURE

menu selection using UP/DOWN buttons.

Press ENTER button to display Password screen.

Follow password entry procedure found in ControlTech™ Calibration manual.

Delete Presets

Delete Presets function allows user to delete all presets at once.

From Configure menu, use UP/DOWN buttons to highlight

DELETE PRESET

selection then press ENTER

button.

Delete Presets confirmation screen is displayed.

Use UP/DOWN buttons to select YES or NO selection.

Press ENTER button to accept selection and exit to Configure menu.

Note: If Delete Presets is selected without a Preset configured, following screen is displayed:

LOCKED

PRESS TO

CONT.

NO PRESETS

PRESS TO

CONT.

NO PRESETS

PRESS TO

CONT.

UP/DOWN buttons

DELETE PRESETS

YES

ENTER

button

UP/DOWN buttons

EXIT

MODE SETUPs

PRESET LOCK
DELETE PRESETS

Delete Presets menu

EXIT

MODE SETUP
PRESET LOCK

DELETE PRESETS

CLEAR DATA

CYCLE COUNT

SETTINGS

CONFIGUREs

UP/DOWN buttons

ENTER PASSWD

EXIT

LANGUAGE

SET HEAD LENGTH

SHOW DATA

ENTER
button

held

ENTER
button

Password screen

DEG

Summary of Contents for ControlTech CTLNK1R240





































Search results

Summary of Contents for ControlTech CTLNK1R240

Reviews:

Related manuals for ControlTech CTLNK1R240

Brands by name

Popular brands

Snap-On ControlTech CTLNK1R240, Manual

Search results

Summary of Contents for ControlTech CTLNK1R240

Reviews:

Related manuals for ControlTech CTLNK1R240

Brands by name

Popular brands