SMSC USB3290 Datasheet Download Page 1

Page: 1 / 46

SMSC USB3290

DATASHEET

Revision 1.5 (11-02-07)

Datasheet

PRODUCT FEATURES

USB3290

Small Footprint Hi-Speed
USB 2.0 Device PHY with
UTMI Interface

Available in a 40 ball lead-free RoHS compliant

(4 x 4 x 0.9mm) VFBGA package

Interface compliant with the UTMI specification

(60MHz, 8-bit bidirectional interface)

Only one required power supply (+3.3V)

Supports 480Mbps Hi-Speed (HS) and 12Mbps Full

Speed (FS) serial data transmission rates

Integrated 45

and 1.5k

termination resistors

reduce external component count

Internal short circuit protection of DP and DM lines

On-chip oscillator operates with low cost 24MHz

crystal

Latch-up performance exceeds 150mA per EIA/JESD

78, Class II

ESD protection levels of 5kV HBM without external

protection devices

SYNC and EOP generation on transmit packets and

detection on receive packets

NRZI encoding and decoding

Bit stuffing and unstuffing with error detection

Supports the USB suspend state, HS detection, HS

Chirp, Reset and Resume

Support for all test modes defined in the USB 2.0

specification

55mA Unconfigured Current (typical) - ideal for bus

powered applications.

83uA suspend current (typical) - ideal for battery

powered applications.

Industrial Operating Temperature -40

C to +85

Applications

The USB3290 is the ideal companion to any ASIC, SoC
or FPGA solution designed with a UTMI Hi-Speed USB
device (peripheral) core.

The USB3290 is well suited for:

Cell Phones

MP3 Players

Scanners

External Hard Drives

Digital Still and Video Cameras

Portable Media Players

Entertainment Devices

Printers

Summary of Contents for USB3290















































Search results

Summary of Contents for USB3290

Reviews:

Related manuals for USB3290

Brands by name

Popular brands

SMSC USB3290, Datasheet

Search results

Summary of Contents for USB3290

Reviews:

Related manuals for USB3290

Brands by name

Popular brands