manualshive.com logo in svg

SMSC LAN9312, Datasheet

The SMSC LAN9312 is a highly efficient and reliable Ethernet switch designed for seamless LAN connectivity. To fully understand its features and operation, we provide a comprehensive user manual available for free download in datasheet format. Obtain your copy today from our manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface

Datasheet

SMSC LAN9312

59

Revision 1.4 (08-19-08)

DATASHEET

 

register. When Auto-negotiation is enabled and the MANUAL_FC_x bit is cleared, the switch port flow
control enables during full-duplex are determined by Auto-negotiation.

Note:

The flow control values in the 

Port x PHY Auto-Negotiation Advertisement Register

( P H Y _ A N _ A D V _ x )

  a n d  

Vi r t u a l   P H Y   A u t o - N e g o t i a t i o n   A d v e r t i s e m e n t   R e g i s t e r

(VPHY_AN_ADV)

 are not affected by the values of the manual flow control register. Refer to

Section 7.2.5.1, "PHY Pause Flow Control," on page 92

 and 

Section 7.3.1.3, "Virtual PHY

Pause Flow Control," on page 98

 for additional information on PHY and Virtual PHY flow

control settings respectively.

Note 6.1

If Auto-negotiation is enabled and complete, but the link partner is not Auto-negotiation
capable, half-duplex is forced via the parallel detect function.

Note 6.2

For the Port 1 and Port 2 PHYs, these are the bits from the 

Port x PHY Auto-Negotiation

Advertisement Register (PHY_AN_ADV_x)

 and 

Port x PHY Auto-Negotiation Link Partner

Base Page Ability Register (PHY_AN_LP_BASE_ABILITY_x)

. For the Virtual PHY, these

are the local/partner swapped outputs from the bits in the 

Virtual PHY Auto-Negotiation

Advertisement Register (VPHY_AN_ADV)

 and 

Virtual PHY Auto-Negotiation Link Partner

Base Page Ability Register (VPHY_AN_LP_BASE_ABILITY)

. Refer to 

Section 7.3.1,

"Virtual PHY Auto-Negotiation," on page 96

 for more information.

Table 6.1  Switch Fabric Flow Control Enable Logic

CASE

MANUAL_FC_X

AN EN

ABLE

AN COMPLETE

LP AN ABLE

DUPLEX

AN PA

USE

ADVERTISEMENT

(

Note

6.2

)

AN ASYM 

PAU

S

E

ADVERTISEMENT

(

Note

6.2

)

LP P

A

USE

ABILI

TY

(

Note

6.2

)

LP ASYM

 P

A

USE

ABILI

TY

(

Note

6.2

)

RX FLOW C

O

NTROL

ENABLE

RX FLOW C

O

NTROL

ENABLE

-

1

X

X

X

Half

X

X

X

X

0

BP_EN_x

-

X

0

X

X

Half

X

X

X

X

0

BP_EN_x

-

1

X

X

X

Full

X

X

X

X

RX_FC_x

TX_FC_x

-

X

0

X

X

Full

X

X

X

X

RX_FC_x

TX_FC_x

1

0

1

0

X

X

X

X

X

X

0

0

2

0

1

1

0

Half  (

Note 6.1

)

X

X

X

X

0

BP_EN_x

3

0

1

1

1

Half

X

X

X

X

0

BP_EN_x

4

0

1

1

1

Full

0

0

X

X

0

0

5

0

1

1

1

Full

0

1

0

X

0

0

6

0

1

1

1

Full

0

1

1

0

0

0

7

0

1

1

1

Full

0

1

1

1

0

1

8

0

1

1

1

Full

1

0

0

X

0

0

9

0

1

1

1

Full

1

X

1

X

1

1

10

0

1

1

1

Full

1

1

0

0

0

0

11

0

1

1

1

Full

1

1

0

1

1

0

Summary of Contents for LAN9312











































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LAN9312

UNICOM DynaGST/2402G GEP-33224T-1 Specifications preview
DynaGST/2402G GEP-33224T-1
Brand: UNICOM Pages: 1
UNICONTROL Electronic Cleveland Controls RSS-498-013 Manual preview
Cleveland Controls RSS-498-013
Brand: UNICONTROL Electronic Pages: 2
K-Dyne OMP L80-P Manual preview
OMP L80-P
Brand: K-Dyne Pages: 10
Inline MSV0502 Operation Manual preview
MSV0502
Brand: Inline Pages: 26
Delta Electronics SK1027 Specifications preview
SK1027
Brand: Delta Electronics Pages: 1
Hirschmann OS20-001000T5T5TAFUHB User Manual preview
OS20-001000T5T5TAFUHB
Brand: Hirschmann Pages: 40
S+S Regeltechnik Premasreg 716 Series Operating Instructions, Mounting & Installation preview
Premasreg 716 Series
Brand: S+S Regeltechnik Pages: 32
3Com 3C17205 - SuperStack 3 Switch 4400 PWR Getting Started Manual preview
3C17205 - SuperStack 3 Switch 4400 PWR
Brand: 3Com Pages: 90
Balluff BNI EIP-950-000-Z009 User Manual preview
BNI EIP-950-000-Z009
Brand: Balluff Pages: 12
Ruby Tech GS-2108C User Manual preview
GS-2108C
Brand: Ruby Tech Pages: 254
Cabletron Systems SmartSTACK 100 ELS100-16TX Getting Started preview
SmartSTACK 100 ELS100-16TX
Brand: Cabletron Systems Pages: 16
Radio Systems HUB16-DC Technical Manual preview
HUB16-DC
Brand: Radio Systems Pages: 19
3onedata IES2008 Quick Installation Manual preview
IES2008
Brand: 3onedata Pages: 2
Grizzly G8988 Instructions preview
G8988
Brand: Grizzly Pages: 2
ABM AstroBox User Manual preview
AstroBox
Brand: ABM Pages: 8
BENDIX SL-3-SL-4 STOP LIGHT SWITCH Manual preview
SL-3-SL-4 STOP LIGHT SWITCH
Brand: BENDIX Pages: 4
MLis MLB-E4203-28-F User Manual preview
MLB-E4203-28-F
Brand: MLis Pages: 85
Intellinet 560641 Instructions Manual preview
560641
Brand: Intellinet Pages: 12

Brands by name

Popular brands

Load more brands