Smith 19A Series Installation Instructions Manual Download Page 11

19A SERIES BOILER

INSTALLATION INSTRUCTIONS

vision problems
loss of muscle control
weakness

dizziness
headaches
nausea

WARNING

shortness of breath
unclear thinking
unconsciousness

Any appliance that burns natural gas, propane gas, fuel oil, wood or coal is capable of producing carbon
monoxide (CO).

Carbon Monoxide (CO) is a gas which is odorless, colorless and tasteless but is very toxic.

If your Smith boiler is not working properly, or is not vented properly, dangerous levels of CO may accumu-
late.  CO is lighter than air and thus may travel throughout the building.  

BRIEF EXPOSURE TO HIGH

CONCENTRATIONS OF CO, OR PROLONGED EXPOSURE TO LESSER AMOUNTS OF CO MAY RE-
SULT IN CARBON MONOXIDE POISONING.

EXPOSURE CAN BE FATAL AND EXPOSURE TO HIGH CONCENTRATIONS MAY RESULT IN THE
SUDDEN ONSET OF SYMPTOMS INCLUDING UNCONSCIOUSNESS.

Symptoms of CO poisoning include the following:

The symptoms of CO poisoning are often confused with those of influenza, and the highest incidence of
poisoning occurs at the onset of cold weather or during flu season.  A victim may not experience any symp-
toms, only one symptom, or a few symptoms.  Suspect the presence of carbon monoxide if symptoms tend to
disappear when you leave your home.

The following signs may indicate the presence of carbon monoxide:
     • Hot gases from appliance, venting system, pipes or chimney, escaping  into the living space.
     • Flames coming out around the appliance.
     • Yellow colored flames in the appliance.
     • Stale or smelly air.
     • The presence of soot or carbon in or around the appliance.
     • Very high unexplained humidity inside the building.

If any of the symptoms of CO poisoning occur, or if any of the signs of carbon monoxide are present,

VACATE THE PREMISES IMMEDIATELY AND CONTACT A QUALIFIED HEATING SERVICE COMPANY
OR THE GAS COMPANY OR THE FIRE DEPARTMENT.

To reduce the risk of CO poisoning, have your heating system "tuned up" by a licensed heating contractor or
the gas company -- preferably before each heating season.  Also have the service company check your
chimney or vent pipes for blockage.
Your home should also be adequately ventilated, particularly if you have insulated your home.

ONLY QUALIFIED, LICENSED SERVICE CONTRACTORS SHOULD PERFORM WORK

ON YOUR SMITH BOILER.

WARNING

Install, operate and maintain unit in accordance with manufacturer's instructions to avoid exposure to fuel
substances or substances from incomplete combustion which can cause death or serious illness.  The State
of California has determined that these substances may cause cancer, birth defects, or other reproductive
harm.  Also, install and service this product to avoid exposure to airborne particles of glasswool fibers and/or
ceramic fibers known to the State of California to cause cancer through inhalation.

PAGE 11

Summary of Contents for 19A Series













Reviews: