Smith & Noble Fusion Hardware Step By Step Installation Instructions Download Page 2

2

800.248.8888 

1 smithandnoble.com 

A Smooth Set-Up

We want you to love your new hardware and that includes 
having a smooth installation experience. We suggest saving 
this  guide.  If  you  encounter  any  difficulties  or  questions, 
please reach out to us for help. It’s why we’re here. Call us at 

800.248.8888

 for more info on installation. 

We recommend you hold on to all packaging until your 
hardware is fully installed. Should something go wrong (we 
strongly doubt it), we want any potential returns to be a 
painless as possible. 

Customer Service Hours 
Monday — Friday:  6am — 6pm PT 
Saturday — Sunday:  7am — 4pm PT
smithandnoble.com

Everything

You Need

Table of Contents

Step 1 -  

Getting Started  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 

Overview - 

   Wall Mount Double Corner Rod Set  . . . . . . . . . . . . . . . . 4

Step 2 -

  

Mounting the Brackets   . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6 

Step 3 - 

 

Attaching the Rod Connector . . . . . . . . . . . . . . . . . . . . . . 7

Step 4 - 

 

Attaching the Finials and Rings  . . . . . . . . . . . . . . . . . 8 - 9

Step 5 - 

 

Securing Rod to Brackets  . . . . . . . . . . . . . . . . . . . . . . . . . 9

Accessories - 

 Baton/Wand  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Accessories - 

 Ball Tiebacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Accessories - 

 Hold Back  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 13  

Care & Cleaning    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 

Warranty   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Summary of Contents for Fusion Hardware









Reviews: