background image

 

 

24 

 

6.1

 

CHARGING THE BATTERY 

 

Apply the brakes to the castors before charging. Also do not use the chair whilst 
charging. 

 

When the battery is low a buzzer will sound. When this happens plug the charging cable 
into the socket on the battery pack assembly on the push handle of the chair. 

 

Plug the other cable into a mains socket and turn on to begin charging the battery. 

 

The battery will become fully charged in approximately 6 hours. 

6.2

 

DAILY CHECKS 

 

Check for signs of wear, tear or damage

 

 

Check for missing parts

 

 

Check  that  all  screws  are  present  and  tighten  correctly,  and  are  not  cross-threaded  or 

damaged

 

 

Check all straps for fraying, and that buckles are not missing/damaged

 

 

Check that the castors run freely and the brakes on each castor function correctly 

 

Check that the high-low actuator feature operates correctly

 

 

Check that the tilt-in-space feature operates correctly

 

 

Check that the footplate is set to the correct height for the client, and that it is securely in 

place.

 

6.3

 

SERVICE INTERVAL 

The Broo Seating System should be serviced every 12 months.  Servicing must only 
be  undertaken  by  a  Smirthwaite  Ltd  service  engineer,  or  by  a  Smirthwaite  Ltd  trained 
representative.   

6.4

 

NOMINAL SERVICE LIFE 

Your product has a nominal service life of 7 years, during which full post-sales support will 
be available with regard to spares and servicing. 

Product service life has been determined based upon the design complexity of product, and 
the anticipated exposure to normal use.   

Good practice dictates all Smirthwaite Ltd products have been designed and manufactured 
to  high  levels  of  safety  and  quality,  and  will  meet  requirements  of  normal  use  when 
maintained in line with our servicing recommendations. 

Summary of Contents for BROOKFIELD HI-LO

































Reviews: