OPERATION
When receiving a SMINN transmitter code, the receiver
checks if it is registered in the inserted memory. If
it is registered and not blocked, it will activate the
corresponding relay.
ERASING THE MEMORY
The internal memory can only be erased when an SMINN
programming console and knowing its PIN, avoiding
accidental or malicious erasures.
BLOCKING A CODE IN THE MEMORY
A transmitter code cannot be simply erased from the
memory, but it can be blocked so it won’t work anymore.
Blocking codes in the memory can only be done using an
SMINN programming console and knowing its PIN.
MANUAL PROGRAMMING
Step by step instructions on how to program a receiver are
detailed next. The first code must be stored following all
these steps. For new codes after the first one, omit step 3:
1.
Press and hold the programming button (fig. 1 –
component 2).
2.
Press the button of the transmitter channel we want to
learn that will be assigned to K1 in the receiver. When
receiving the code and channel sent by the transmitter,
the receiver will store it in its memory and beep twice
as a validation signal.
3.
ONLY TO STORE/LEARN THE FIRST CODE AND IF
THE MEMORY IS CONFIGURED AS DUAL-CHANNEL.
Press the channel button of the transmitter we want
to assign to Output 2 of the receiver. When receiving
the code and channel send by the transmitter, the
receiver will store/learn it in the memory and will
beep THREE times as a validation signal.
4. Release the programming button of the receiver.
Repeat this process with as many transmitter codes as you
want to manually register in the memory, using the same
channel assigned to Output 1 with the first transmitter.
Pressing any other channel will not have any effect.
REGISTRATION VIA RADIO
Depending on the level of security configured in the
receiver’s memory it is possible to register transmitter
codes via radio.
Security level 1 (Basic)
.- Transmitter can be programmed
in invitation mode knowing the PIN (the certified number
of the installation) using a SMINN programming console.
Invited transmitters are automatically registered by level 1
receivers.
Security level 2 (Intermediate)
.- Transmitters already in use
can INVITE new transmitters that share the same PIN (the
certified number of the installation).
Security level 3 (Advanced)
.- Emitters will be registered in
the receiver manually. Radio-based registration is disabled.
CODE REPLACEMENT DUE TO LOSS
This function allows to replace a transmitter code stored in
the receiver with a new one, be it due to loss or mislaying.
The replacement of a transmitter code is only possible
with a SMINN programming console. Knowing the
PIN of the installation and the code number of the lost
transmitter is required.
BACKUP
Although the device is protected against power line
disturbances and electrical surges, it is important to
keep a backup of the memory card in case of breakdown
or damages caused by external circumstances such as
electric storms, theft, improper handling, etc.
INSTALLATION
SMINN receivers are prepared to be easily fixed on a
wall using the supplied wall plugs and screws. Before
connecting or operating the device the power supply
switch or differential shall be disconnected.
Specialized and/or skilled personnel will do the installation,
using properly protected cable of enough gauge.
Take into account that devices permanently connected to
the mains need to have an accessible connection device
(i.e. a magnetothermic switch).
The wiring should be done following the instructions
printed in the serigraphy of the circuit board.
Make sure that the memory is inserted and properly
configured. After programming and verifying the
equipment, close the case with the supplied top.
SMINN RECEIVERS ARE EQUIPPED WITH A LED TO
LET KNOW IF THHE DEVICE IS POWERED
Note
: Reinforced concrete, metallic components and/
or any other receiving device reduce dramatically the
radiofrequency signal, so installation close to these
elements should be avoided.
USE LIMITATIONS
Operation is not guaranteed when installed in different
equipment than the specified.
THE USAGE INSTRUCTIONS OF THIS DEVICE SHALL
BE HANDED TO THE USER, WHO WILL HAVE THEM
IN THEIR POSSESSION. IF THEY ARE MISLAID, THE
USER CAN ASK FOR A COPY OR DOWNLOAD IT
DIRECTLY FROM THE WEBSITE WWW.SMINN.COM
The manufacturer keeps the right to modify the content of
this document or the product without prior warning.
The equipment must be manipulated only by specialized
and/or skilled personnel.
SAT
M
434/868
RECEIVER
INSTRUCTION MANUAL
DESCRIPTION
SMINN SAT M receivers are developed with
state-of-the-art electronics and technology.
They provide a high degree of operating
reliability and security. They have a robust
copy protection and anti-burglar system.
They are designed to send the activation/
deactivation order to SMINN motor
controllers, alarm systems, access control
systems, home automation systems, etc.
They are suitable for industrial, commercial
and/or residential environments.
Devices that are built using high quality
materials and components and the latest
technology. They are made taking into
account the current regulations for usage
in residential, commercial and light industry
environments.
innovative in electronics
