OPERATION
When a SMINN transmitter’s code is received, the receiver checks the integrity
of that code and if it is registered in the memory. Once verified, it activates the
corresponding relay.
ERASE MEMORY
Stored SMINN transmitters’ codes can only be deleted completely by erasing
the memory. To do so, these steps should be followed:
Disconnect the power supply of the equipment.
•
Press and hold the programming button (PROG).
•
Connect the power supply while holding (PROG).
•
Wait 8 seconds until the LED is switched on.
•
Release the programming button (PROG) for 2 seconds.
•
Press and hold the programming button (PROG).
•
The LED turns off.
•
Wait 8 seconds until the LED flashes.
•
Release the programming button (PROG).
•
Wait for the validation beep.
•
After this process, the receiver has been erased and the memory checked,
leaving it ready to register transmitters.
TRANSMITTER PROGRAMMING
SMINN’s SAT M series B can store up to a total of 35 transmitters with
compatible PIN. Before registering transmitters, make sure they have the same
PIN.
If it is the first installation, previously we have to delete and, optionally,
customize the receiver’s memory. Repeat the process for as many transmitters
as we want to register.
If we try to register more than 35 transmitters, the receiver will answer with a
long beep indicating that the memory is full. The first registered transmitter
indicates the working channel of the K1 relay in the receiver, the rest of
transmitters should be registered using the same button of the channel as the
first transmitter.
MANUAL PROGRAMMING
To register transmitters manually using the programming button, proceed as
follows:
Turn on the device and wait 5 sec.
•
Press and hold the receiver’s programming button (PROG).
•
Press and hold the button of the transmitter’s channel on the (transmitter/
•
one) we want to register.
Check that the led is blinking (SCAN mode).
•
Wait for the validation beep.
•
Release the transmitter button.
•
Release the programming button of the receiver (PROG).
•
REGISTRATION VIA RADIO
Only a registered transmitter can invite or grant self-registration capabilities to
other SMINN transmitters with the same PIN.
Registration by invitation
Press and hold the registered transmitter’s 1st and 2nd buttons (MASTER
•
transmitter).
Wait for 5 seconds until the LED is on in both transmitters.
•
Release 1st and 2nd buttons of both emitters (the led remains on).
•
Ensure you are close to the receiver to guarantee communication (1 to
•
10m).
Press and hold the transmitter’s 1st button.
•
Wait for the validation beep (learning mode for 8 sec).
•
Press and hold the corresponding button on the transmitter channel we
•
want to register.
Wait for the validation beep.
•
Release the button of the new transmitter.
•
Registration by invitation
Press and hold the registered transmitter’s 1st and 2nd buttons (MASTER
•
transmitter).
Press and hold the new transmitter’s 1st and 2nd buttons (it must have the
•
same PIN).
Wait for 5 seconds until the LED is on in both transmitters.
•
Release 1st and 2nd buttons of both emitters (the led remains on).
•
Take the Master transmitter’s led near the new transmitter’s SYNC area..
•
Press and hold the Master transmitter’s 1st button.
•
Wait until the new transmitter’s led flashes 5 times.
•
Release the Master’s button.
•
Ensure you are close to the receiver to guarantee communication (1 to
•
10m).
Press and hold the corresponding button on the transmitter channel we
•
want to register.
Wait for the validation beep
•
Release the button of the new transmitter.
•
CODE REPLACEMENT DUE TO LOSS
This function allows to replace a transmitter code stored in the receiver with a
new one, be it due to loss or mislaying. The replacement of a transmitter code
is only possible with a SMINN programming console. Knowing the PIN of the
installation and the code number of the lost transmitter is required.
INSTALLATION
SMINN’s motor controller is ready to be easily fixed on a wall using the
supplied wall plugs and screws.
Before connecting or operating the device, the power supply switch or
differential shall be disconnected.
Specialized and/or skilled personnel will do the installation, using properly
protected cable of enough gauge and taking into account that devices
permanently connected to the mains need to have an accessible connection
device (i.e. a magnetothermic switch).
The wiring should be done following the instructions printed in the serigraphy
of the circuit board. After programming and verifying the equipment, place the
lid on the front of the box, with the supplied screws.
SMINN’S MOTOR CONTROLLERS INCLUDE A LIGHT SIGNAL TO KNOW
IF THE EQUIPMENT IS POWERED.
Note:
Reinforced concrete, metallic components and/or any other receiving
device reduce dramatically the radiofrequency signal, so installation close to
these elements should be avoided.
BOX
S
140/180 B
RECEIVER
INSTRUCTION MANUAL
DESCRIPTION
SMINN’s SAT M series B receivers are developed using
state-of-the-art devices. They include a receiver with
capacity to store up to 35 transmitters. Its memorization
capability via radio or using a simple push-button makes
it easy and handy. They have a robust copy protection
and anti-burglar system.
They are designed to send the activation/deactivation
order to SMINN motor controllers, alarm systems, access
control systems, home automation systems, etc.
These devices are built using high quality materials
and components and the latest technology. They are
devices that observe the current regulations for usage in
residential, commercial and light industry environments.
innovative in electronics
