background image

GB 5

Do not use extension leads or multi sockets.
Electrical connections must be made in accordance with local regulations.

1)  Warning - this washing machine must be earthed

This washing machine is normally supplied with a mains lead having a plug fitted in the factory which has
been checked for correct earth continuity.
If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with a plug,
you should fit a suitable new, good quality plug by following the instructions in (2) below.
Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it be
inserted into a socket.

2)  CONNECTION TO A REWIRABLE PLUG - to be carried out only by a qualified electrician

The wires in the mains lead are coloured in accordance with the following code:

BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)

   

To fit a new plug, proceed as follows:

   

2.1)  Polarized Plugs (e.g. 3 pin, 13 amp plug conforming to

   

 

BS 1363A)

   

a. 

  The GREEN AND YELLOW wire must be connected to the

   

 

terminal in the plug which is marked with the letter “E” or by

   

 

the Earth symbol         or coloured green and yellow.

   

b. 

  The BLUE wire must be connected to the terminal which is

   

 

marked with the letter “N” or coloured blue.

   

c. 

  The BROWN wire must be connected to the terminal  

 

   

 

which is marked with the letter “L” or coloured brown.

2.2) Non-polarized plugs (e.g. 2 pin with side earth contact)

The wire which is coloured GREEN AND YELLOW must be connected to the earth contact. The other two
wires should be connected to the two pins, irrespective of colour.

   

FUSE REPLACEMENT

   

If the mains lead of this washing machine is fitted with a BS 1363A 

   

13 amp fused plug, replace the fuse only with an A.S.T.A. approved type

   

conforming to BS 1362 and proceed as follows:

   

Remove the fuse cover (A) and the fuse (B).

   

Fit the replacement 13 A fuse into the fuse cover.

   

Refit both into the plug.

   

For all other types of plug, the supply socket should be protected by

   

a 16 A fuse or circuit breaker at the distribution board.

ELECTRICAL CONNECTION

Summary of Contents for TLS8-1


















Reviews: