Smeg SW106, Manual

Page: 3 / 18

3
EN
the product into its place after installation or
cleaning procedures.
Appropriate installation location
t 1MBDFUIFNBDIJOFPOBSJHJEGMPPS%POPU
place it on a long pile rug or similar surfaces.
t 5PUBMXFJHIUPGUIFXBTIJOHNBDIJOFBOEUIF
ESZFSXJUIGVMMMPBEXIFOUIFZBSFQMBDFE
on top of each other reaches to approx.
180 kilograms. Place the product on a solid
and flat floor that has sufficient load carrying
capacity!
t %POPUQMBDFUIFQSPEVDUPOUIFQPXFSDBCMF
t %POPUJOTUBMMUIFQSPEVDUBUQMBDFTXIFSF
UFNQFSBUVSFNBZGBMMCFMPX$
t 1MBDFUIFQSPEVDUBUMFBTUDNBXBZGSPNUIF
edges of other furniture.
Removing packaging reinforcement
5JMUUIFNBDIJOFCBDLXBSETUPSFNPWFUIF
packaging reinforcement. Remove the packaging
SFJOGPSDFNFOUCZQVMMJOHUIFSJCCPO
Removing the transportation locks
A
%POPUSFNPWFUIFUSBOTQPSUBUJPOMPDLTCFGPSF
taking out the packaging reinforcement.
A
3FNPWFUIFUSBOTQPSUBUJPOTBGFUZCPMUTCFGPSF
operating the washing machine, otherwise,
UIFQSPEVDUXJMMCFEBNBHFE
-PPTFOBMMUIFCPMUTXJUIBTQBOOFSVOUJMUIFZ
rotate freely (C).
3FNPWFUSBOTQPSUBUJPOTBGFUZCPMUTCZUVSOJOH
them gently.
"UUBDIUIFQMBTUJDDPWFSTTVQQMJFEJOUIF6TFS
.BOVBMCBHJOUPUIFIPMFTPOUIFSFBSQBOFM
(P)
C
,FFQUIFUSBOTQPSUBUJPOTBGFUZCPMUTJOBTBGF
place to reuse when the washing machine
OFFETUPCFNPWFEBHBJOJOUIFGVUVSF
C
Never move the product without the
USBOTQPSUBUJPOTBGFUZCPMUTQSPQFSMZGJYFEJO
place!
Connecting water supply
C
5IFXBUFSTVQQMZQSFTTVSFSFRVJSFEUPSVO
UIFQSPEVDUJTCFUXFFOUPCBST o
.1B*UJTOFDFTTBSZUPIBWFoMJUFSTPG
water flowing from the fully open tap in one
minute to have your machine run smoothly.
Attach a pressure reducing valve if water
pressure is higher.
C
*GZPVBSFHPJOHUPVTFUIFEPVCMFXBUFSJOMFU
QSPEVDUBTBTJOHMF DPMEXBUFSJOMFUVOJUZPV
must install the supplied stopper to the hot
XBUFSWBMWFCFGPSFPQFSBUJOHUIFQSPEVDU
"QQMJFTGPSUIFQSPEVDUTTVQQMJFEXJUIBCMJOE
stopper group.)
C
*GZPVXBOUUPVTFCPUIXBUFSJOMFUTPGUIF
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
TVQQMJFEXJUIBCMJOETUPQQFSHSPVQ
A
Models with a single water inlet should not
CFDPOOFDUFEUPUIFIPUXBUFSUBQ*OTVDI
a case the laundry will get damaged or the
product will switch to protection mode and will
not operate.
A
%POPUVTFPMEPSVTFEXBUFSJOMFUIPTFTPO
UIFOFXQSPEVDU*UNBZDBVTFTUBJOTPOZPVS
laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product.
3FEIPTF MFGU NBY$JTGPSIPUXBUFS
JOMFUCMVFIPTF SJHIU NBY$JTGPSDPME
water inlet.
A
Ensure that the cold and hot water
connections are made correctly when
JOTUBMMJOHUIFQSPEVDU0UIFSXJTFZPVSMBVOESZ
will come out hot at the end of the washing
process and wear out.
5JHIUFOBMMIPTFOVUTCZIBOE/FWFSVTFB
wrench when tightening the nuts.
0QFOUIFUBQTDPNQMFUFMZBGUFSNBLJOHUIF
hose connection to check for water leaks at
UIFDPOOFDUJPOQPJOUT*GBOZMFBLTPDDVSUVSO
off the tap and remove the nut. Retighten
the nut carefully after checking the seal. To
prevent water leakages and damages caused
CZUIFNLFFQUIFUBQTDMPTFEXIFOUIF
machine is not in use.
Connecting to the drain
t 5IFFOEPGUIFESBJOIPTFNVTUCFEJSFDUMZ
connected to the wastewater drain or to the
XBTICBTJO
A
:PVSIPVTFXJMMCFGMPPEFEJGUIFIPTFDPNFT
out of its housing during water discharge.
Moreover, there is risk of scalding due to
high washing temperatures! To prevent such
situations and to ensure smooth water intake
and discharge of the machine, fix the end of
the discharge hose tightly so that it cannot