background image

 

Introduction 

 

1

 

INSTRUCTIONS FOR SAFE AND PROPER USE 

 

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND 
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE 
PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE 
READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE 
USING THE HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. 
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN 
ACCORDANCE WITH THE REGULATIONS IN FORCE.  THIS APPLIANCE IS 
INTENDED FOR FOR DOMESTIC USES AND CONFORMS TO 

EEC 

DIRECTIVES 

 CURRENTLY IN FORCE. THE APPLIANCE IS DESIGNED TO 

CARRY OUT THE FOLLOWING FUNCTIONS: 

COOKING AND HEATING 

FOOD

; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER. 

THE MANUFACTURER DECLINES ALL LIABILITY FOR IMPROPER USE 

.

 

 

 

 

 

DO NOT LEAVE THE PACKAGING MATERIALS UNATTENDED IN THE HOME 
ENVIRONMENT. SEPARATE THE DIFFERENT WASTE MATERIALS FROM 
THE PACKAGING AND DELIVER THEM TO THE NEAREST COLLECTION 
CENTRE FOR RECYCLABLE WASTE. 

 

 

 

REGULATIONS REQUIRE THAT THE APPLIANCE IS EARTHED IN 
ACCORDANCE WITH ELECTRICAL SAFETY REGULATIONS. 

 

 

 

THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND THE 
SOCKET MUST BE OF THE SAME TYPE AND MUST CONFORM TO 
CURRENT REGULATIONS.  
THE POWER SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS 
BEEN BUILT IN. 

NEVER UNPLUG THE APPLIANCE BY PULLING THE POWER SUPPLY 
CABLE

.

 

 

 

 

IMMEDIATELY AFTER INSTALLATION, CARRY OUT A BRIEF INSPECTION 
TEST OF THE APPLIANCE, FOLLOWING THE INSTRUCTIONS BELOW. 
SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE 
POWER SUPPLY AND CONTACT YOUR NEAREST TECHNICAL ASSISTANCE 
CENTRE. 

NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF

 

 

 

 
 

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION  
 

(OFF) WHEN YOU FINISH USING THE HOB. 

 
 

20

 

Summary of Contents for PGF95K

















Reviews: