Smeg P705VT Instruction Manual Download Page 2

Instructions for safe and proper use

 

 

 

19 

1.

 

Instructions for safe and proper use 

 

 

THIS MANUAL IS  AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS 
ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING 
HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING 
THE COOKING HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATION MUST BE 
CARRIED OUT BY QUALIFIED PERSONNEL  IN ACCORDANCE WITH THE REGULATIONS IN FORCE. 
THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT 

REGULATIONS IN FORCE

. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING 

FUNCTIONS: 

COOKING AND HEATING-UP OF FOOD

. ALL OTHER USES ARE CONSIDERED 

IMPROPER.  

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE.

 

 
 

 

 

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT.  SEPARATE THE VARIOUS WASTE 
MATERIALS  AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE. 
 
 
 

 

 

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED ACCORDING TO THE 
METHODS REQUIRED BY SAFETY RULES. 
 
 
 

 

 

THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET MUST BE THE SAME 
TYPE AND MUST CONFORM TO CURRENT REGULATIONS. 
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN. 

NEVER UNPLUG BY PULLING ON THE CABLE.

 

 
 

 

 

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE COOKING 
HOB, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT FUNCTION, 
DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. 

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

 

 

 

 

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE “ZERO” (OFF) POSITION WHEN YOU 
FINISH USING THE HOB. 
 
 
 

 

 

DO NOT PUT

 PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE COOKING HOB 

GRIDS. 
 
 
 

 

 

DO NOT USE

 RECIPIENTS OR GRIDDLE PLATES THAT EXTEND BEYOND THE EXTERNAL 

PERIMETER OF THE HOB. 
 
 
 

 

 

THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME IS 
POSITIONED VISIBLY UNDER THE CASING, ATTACHED TO THIS MANUAL AND APPLIED TO THE 
QUALITY CERTIFICATE.  

THE PLATE ON THE CASING MUST NOT BE REMOVED.

 

 

 

 

THE HOB IS TO BE USED BY ADULTS ONLY

. DO NOT LET UNSUPERVISED CHILDREN PLAY WITH 

THE HOB. 
 
 
 

 

THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE 
ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). 
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF RETURN AND RECYCLING ON 
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT.

 

 

 

 

 

The manufacturer declines all responsibility for damage to persons or things caused 

by non-observance of the above prescriptions or by interference with any part of the 
appliance or by the use of non-original spares. 

 

Summary of Contents for P705VT















Reviews: