background image

Table of Contents

3

EN

1 Installation

8

1.1 Dimension Requirements

8

1.2 Product dimensions

9

1.3 Unpacking, moving and positioning the range

10

1.4 Wall attachment and anti-tip device

12

1.5 Electrical requirements

16

1.6 Gas supply requirements

18

1.7 For the installer

23

WARNING: If the instructions in this manual is not followed exactly, a
fire or explosion may result causing property damage, personal injury
or death.

- Do not store or use gasoline or other flammable vapors or liquids in the 

vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch.
•  Do not use any phone in your building.
•  Immediately call your gas supplier from a neighbor’s phone. Follow the 

gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service 

agency or gas supplier.

NOTE

This appliance must be installed solely and exclusively by a qualified

technician. Any technical procedures must be carried out by an authorized
technician.

Summary of Contents for CPF36UGGAN























Reviews: