Smeg ALFA41XE Instructions For Installation And Use Manual Download Page 2

 

Presentation 

 

1.

 

PRECAUTIONS FOR SAFETY AND USE 

 

 

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD 
CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN'S LIFE 
CYCLE. WE URGE YOU TO READ THIS MANUAL AND ALL THE 
INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE OVEN. 
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN 
COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS OVEN IS 
INTENDED FOR PROFESSIONAL USE AND COMPLIES WITH THE 

EEC 

DIRECTIVES

 CURRENTLY IN FORCE. THE APPLIANCE IS BUILT TO 

PROVIDE THE FOLLOWING FUNCTION: 

COOKING AND HEATING 

FOODS

; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER. 

THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER 
THAN THOSE STATED ABOVE. 

 

 

 

 

NEVER USE PACKAGING RESIDUES UNATTENDED IN THE HOME. 
SEPARATE THE VARIOUS WASTE PACKAGING MATERIALS BY TYPE 
AND CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL 
CENTRE. 
 

 

 

THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE 
WITH ELECTRICAL SYSTEM SAFETY REGULATIONS. 

 

 

IF THE MAIN ELECTRICAL CONNECTION IS TO BE MADE BY MEANS OF 
A PLUG AND SOCKET, THEY MUST BOTH BE OF THE SAME TYPE AND 
MUST BE CONNECTED TO THE POWER SUPPLY LEAD IN 
ACCORDANCE WITH THE RELEVANT REGULATIONS.  

NEVER DISCONNECT THE PLUG BY PULLING ON THE CABLE. 

 

 

 

NEVER OBSTRUCT THE OPENINGS PROVIDED FOR VENTILATION OR 
HEAT DISPERSAL. 

 

 

IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON 
THE OVEN FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN 
THIS MANUAL. IF THE APPLIANCE FAILS TO OPERATE, DISCONNECT 
IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST 
SERVICE CENTRE. 

NEVER ATTEMPT TO REPAIR THE APPLIANCE 

YOURSELF.

 

 

 

AFTER EACH USE OF THE OVEN, ALWAYS CHECK THAT THE 
CONTROL KNOBS ARE TURNED TO

 0

 (OFF). 

20

 

Summary of Contents for ALFA41XE

















Reviews: