SMC Networks ZK2 A Series Page 45 Operation Manual Download

Page: 45 / 80

-44-

No. ZK2-OM01301

■

Plug (For One-touch fitting)

(Purchasing order is available in units of 10 pieces.)

Mounted onto ports which are not used (PV, PS, PD, etc.)

KQ2P- 06

When existing product is used, please be careful with the interchangeability between existing product in the

table below and ZK2□A.

〇

Single unit

New valve assembly of ZK2□A cannot be assembled with the existing products.
(Pilot valve dimension and valve body dimension are different)

Model and Dimensions

Symbol

Applicable size ød

øD

Weight (g)

Note

ø6

White

ø8

20.5

White

ø1/4

”

8.5

Orange

ø5/16

”

20.5

Orange

There are
interference
parts within
shaded area

Existing product

ZK2□A

Grey

Blue

Valve assembly

New valve assembly

Valve body

Summary of Contents for ZK2 A Series

















































































Search results

Summary of Contents for ZK2 A Series

Reviews:

Related manuals for ZK2 A Series

Brands by name

Popular brands

SMC Networks ZK2 A Series, Operation Manual

Search results

Summary of Contents for ZK2 A Series

Reviews:

Related manuals for ZK2 A Series

Brands by name

Popular brands