background image

Port and Cable Assignments

9

Port and Cable Assignments

RJ-45 Port Description

RJ-45 station ports (all port) can be attached to any devices which use a standard 
network interface (e.g., a workstation, server, bridge or router). RJ-45 daisy-chain 
ports (all port) can be cascaded to a station port on similar networking devices (e.g., 
another switch or hub). Use unshielded twisted-pair (UTP) or shielded twisted-pair 
(STP) cable for RJ-45 connections: 100-ohm Category 3, 4 or 5 cable for 10 Mbps 
connections or 100-ohm Category 5 cable for 100 Mbps connections. Also be sure 
that the length of any twisted-pair connection does not exceed 100 meters (328 feet).

Schematics for both straight and crossover twisted-pair cable are shown below

Pin

Assignment

(Station Ports)

Assignment 

(Daisy-Chain Port)

1

Input Receive Data +

Output Transmit 

Data +

2

Input Receive Data -

Output Transmit 

Data -

3

Output Transmit 

Data +

Input Receive Data +

6

Output Transmit 

Data -

Input Receive Data -

4,5,7,

8

Not Used

Not Used

Straight-Through

Crossover

(Switch) (Adapter)

(Switch) (Hub/Switch) 

1   IRD+ 

1 OTD+ 1   IRD+ 

1 IRD+

2   IRD- 

2 OTD- 2   IRD- 

2 IRD-

3   OTD+

3   IRD+ 3   OTD+ 

3 OTD+

6   OTD- 

6   IRD- 6   OTD- 

6 OTD-

Summary of Contents for SMCEZNET-16SW
























Reviews: