background image

iii

C

OMPLIANCES

FCC - Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with instructions, may 
cause harmful interference to radio communications. However, there is no guarantee that the inter-
ference will not occur in a particular installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected

• Consult the dealer or an experienced radio/TV technician for help

Industry Canada - Class B

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital 
apparatus as set out in the interference-causing equipment standard entitled 
“Digital Apparatus,” ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils 
numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils 
Numériques,” NMB-003 édictée par le ministère des Communications.

Japan VCCI Class B

Summary of Contents for RPUPOE









































Reviews: