manualshive.com logo in svg

SMC Networks ISE30A Series, Operation Manual

Share
Download
SMC Networks ISE30A Series Operation Manual Download Page 49

 

-48- 

 

No.PS##-OML0003-B 

 

If the security code is forgotten

 

If the security code is forgotten. 
The following mode is used only when the security code is forgotten. 
 

<Operation> 

Keep pressing the 

 button for 5 seconds or longer in the of measurement mode. 

The current setting "UnL" or "LoC" is indicated. 

 

 
Keep pressing 

 and 

 buttons simultaneously for 5 seconds or longer. 

Then, keep pressing 

 and 

 buttons simultaneously for 5 seconds   

or longer. 

∗

: There is no change of the indication. 

(At this time, if the other operation is performed or no operation is performed 
for 30 seconds or longer, the measurement mode returns.) 
 
 
After that, keep pressing 

 and 

 buttons for 5 seconds or longer. The indication changes to "0000" 

and the security code changing mode returns. 
(At this time, if another operation is performed or no operation is performed for 30 seconds or longer, 
the measurement mode returns.) 
 
Refer to "How to change the security code" on page 46 and decide the security code. 
 
Changed security code is indicated. 
Check and press the 

 button for 1 second or longer. 

The measurement mode returns. 
At this time, if the 

, or 

 button is pressed, changed security code is not entered and the change of 

security code is asked. 

Summary of Contents for ISE30A Series



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands