manualshive.com logo in svg

SMC Networks ISE30A Series, Operation Manual

Share
Download
SMC Networks ISE30A Series Operation Manual Download Page 38

 

-37- 

 

No.PS##-OML0003-B 

 

 

■

Special function setting

 

■

[F90] Setting of all functions 

All functions can be set in series. 
This function is equipped with existing models as well. 

 

<Operation> 

Press the

 

 

or

 

 

button in function selection mode to display [F90]. 

 

Press the

 

 

button. 

  Move on to setting of all functions. 

 

 

 

 

 

 

 

[on] (used) selected 

Setting of each function 

∗

1

 

 
[oFF] (unused) 
selected. 
 
Press the

 

 

button 

to set. 
 
Return to function 
selection mode. 

 

After the change to [oFF] (unused),

press the

 

 

button to set.

 

Return to function selection mode.

 

Press the

 

 

button for 2 
seconds or longer.

 

[F90] setting of all functions completed 

Measurement mode 

 
 

∗

1: Setting of functions 

Every time 

 button is pressed, function turns to page 38. 

Set by 

 or 

 button.   

Refer each paragraph for the detail of setting. 

Setting of all functions 

Press the

 

 

or

 

 

button to select all functions. 

Summary of Contents for ISE30A Series



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands