background image

 

i Safety Instructions

 

i

 Safety 

Instructions 

 

 

Be sure to read and comprehend important cautionary 
notifications in this operation manual before use 

 

 

Do not operate the 

 product

  without the cover panel. 

 

i – 1     Warning:  Before Using Air Dryer 

 

In this chapter, the stated contents are especially about safety way to use the product. for customer. 

An Air Dryer is installed on the downstream of the air compressor to remove moisture. W e, manufacturer, cannot 

take any responsibility  if you use it for any other purpose. 

An Air Dryer works with high voltage and has some parts that gets hot or rotates during operation. Ask vendor if you 

need component replacement and servicing.

  

Not only people handle the air dryer but every people who perform maintenance on or do works related to it should 

read  safety instructions on this operation manual before handling. 

This operation manual is not a general safety manual which is practiced by safety training representatives. 

People who handle this product or work around it need to take training to comprehand inherent risks of it and master 

measures for safety. 

It is usually responsible for super visor to follow the safety instructions, but each operator or maintemance 

representative should do daily operations on their own head. 

Operators and maintemance representatives should take the safety of working place and work environment into 

account. 

It is necessary to think of the safety of working place and work environment  for each task 

Take enough safety training before the operation training. It is very dangerous to do operation training without any 

safety training. Operation training must be paid attention to its safety. 

Keep this operation manual handy for workers related to above contents to refer to anytime. 

  

i – 1 – 1  Meaning of Signs: Caution, Warning, Danger 

These safety instructions are intended to prevent hazardous situation and/or 

product

 damage. 

These instructions indicate the level of potential hazard by signs 

“Caution”, “Warning” 

or

 

“Danger”. 

Contents with these signs state about important instructions concerning safety. Confirm 

where those signs are, and read and comprehend notices and cautionary notices well before 

handling. 

 

“Caution”, “Warning” 

or

 “Danger” 

is the

 

order of

 

importance (Danger>Warning>Caution). Followings 

are the meanings of those signs. 

 

Danger 

Statements with the “Danger” sign explain about conditions in which there is a 

possible result of serious injury or loss of life if someone handles wrongly during 

operation or maintenance and did not follow the procedure to avoid danger. 

i

 - 

Summary of Contents for IDU3E-10






























Reviews: